KSH International E-P432 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 43

background image

KSH International CO., LTD.

11

Front Side

Power Supply

The e-Net TCP/IP converter is powered by a single 9

～

12V DC(Inner positive/outer

negative) power supply and 500mA of current. A suitable power supply adapter is part
of the packaging. Connect the power line to the power outlet at the

right side of e-Net

TCP/IP converter and put the adapter into the socket. If the power is properly supplied,
the “SYS” green color LED will be on.

LAN

Serial I/O Port

RS-485/RS-422

DC-In

Power Outlet

LAN Port

The connector for network is the usual RJ45. Simply connect it to your network
switch or Hub. When the connection is made, the LAN LED indicator will light.
When data traffic occurs on the network, red (Rx/Tx) indicator will blink during data
transferring and receiving.

Serial I/O Port of RS-422/RS-485

Connect the serial data cable between the converter and the serial device. Follow the
parameter setup procedures to configure the converter (see the following chapters ).

«
...
10
11
12
13
14
...
»

Содержание E-P432












































Отзывы:

Нет отзывов

Похожие инструкции для E-P432

Бренд: ABB Страницы: 78

Бренд: ABB Страницы: 62

OTEC IEWQ Series

Бренд: Omega Страницы: 29

Бренд: Enerdrive Страницы: 24

Бренд: B&B Electronics Страницы: 2

Бренд: 3onedata Страницы: 3

Бренд: Racal Instruments Страницы: 12

Бренд: ICP DAS USA Страницы: 8

Бренд: Vanner Страницы: 28

ServeMaster 1600MV

Бренд: IBC SOLAR Страницы: 58

Бренд: Airpax Dimensions Страницы: 6

Бренд: Nuova Marea Страницы: 9

Бренд: Tyba Страницы: 14

Бренд: DAD Страницы: 31

Бренд: AJA Страницы: 43

Бренд: Briggs & Stratton Страницы: 36

Бренд: ADF Web Страницы: 29

Бренд: Sungrow Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды