KSB GIW LCC 100-400 Скачать руководство пользователя | Manualshive

Страница: 33 / 44

background image

LCC

33

11.4 Diverter

One of the product improvements to the GIW LCC Expeller pumps is the addition of a Diverter to further
reduce the accumulation of solids in the expeller chamber. This is a urethane part that is pressed into the hub
area of the pump casing. See the LCC Maintenance Manual for specific pump disassembly procedures

.

Installation instructions:

Disable the driver to prevent pump operation

Drain the system and remove the suction pipe

Remove the suction liner and impeller

Clean the hub area of the pump casing

Removal of the pump casing will be necessary for the LCC 9 Metal & Rubber lined pumps, see figure
below.

Clean the face of the expeller hub

Position the Diverter with the tapered ring facing into the pump as shown below

Press the Diverter completely back against the expeller plate –

If necessary, seat the Diverter using a small hammer and a smooth wood block cut to fit between the lip
and casing

Place a small straight edge along the back of the pump casing to verify the diverter is flush to the casing
plane within 3 mm.

Place two (2) new impeller release gaskets on the shaft

Coat the shaft threads with anti-seize

Thread the impeller on the shaft and hand tighten

Reinstall the suction liner and adjust the impeller nose gap

Connect the suction piping and restart the pump

«
...
31
32
33
34
35
...
»

Содержание GIW LCC 100-400













































Отзывы:

Нет отзывов

Похожие инструкции для GIW LCC 100-400

Бренд: Zehnder Rittling Страницы: 64

Бренд: Jacuzzi Страницы: 8

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 24

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 68

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 24

Бренд: Oasis Страницы: 44

Бренд: Speck Страницы: 24

Бренд: A.O. Smith Страницы: 4

Бренд: Battery Watering Technologies Страницы: 2

Бренд: Waterax Страницы: 6

Бренд: Pattfield Ergo Tools Страницы: 162

Goulds AquaBoost Advanced

Бренд: Xylem Страницы: 36

FloJet 3426 Series

Бренд: Xylem Страницы: 6

Бренд: Water Ace Страницы: 16

Бренд: Bock Water heaters Страницы: 56

Бренд: VARISCO Страницы: 16

Бренд: KSB Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды