background image

                                      SLYSEL 
                             Version 20090112.20090202     GIW Industries, Inc. 
Item # : 5012-13012-15                                     Grovetown, GA  USA 
Reference: Metso Minerals                                  Date: Feb-05-2009  
Application: Mill Product Pump , Constellation             Time: 16:02:15   
 
LCC-H200-610.5M A 8 X 10 LCC 24 (XH), 125MM O IL CBA MECHANICAL SEAL             
-------- SELECTED PUMP with ALL VALUES SCALED to NEW SPEED & TURNDOWN --------- 
S  8 x10 LCC 24(XH)    C H 7-  /  / 3ME  125MM   5017X-07 E 54 -05 B 27A-98 
**************** PLEASE NOTE ALL DIAMETERS ARE IN INCHES ***************** 
R.P.M            962.5 | T/D RATIO (THEO)  1.000 | PERIPHERAL VEL  6051.9 SFPM 
EFF. (SLURRY)     73.0 | FULL    IMP DIA   24.02 | THROAT     VEL    16.7 ft/s 
EFF. (WATER)      74.8 | THEORET IMP DIA   24.02 | BRANCH     VEL    15.4 ft/s 
NPSH RQD (ft)      7.4 | ACTUAL  IMP DIA   24.02 | SUCTION    VEL     9.8 ft/s 
Conc. by WT (%)   56.5 | SOLIDS EFFECT HEAD 1.88%| SOLIDS EFFECT EFF     2.39% 
Conc. by Vol(%)   30.8 | NPSHA (ft)          0.0 | SPHERE PASSAGE     3.7 in 
Pump Ns (US)    1184.4 | Suction Ns (US) 10175.0 | ROTATION            RH 
 
         Flow(GPM)   Head(ft)       Eff.     HP w/SGM    NPSHR(ft) 
               0.0     197.0         0.0      101.4        5.2 
             870.0     192.0        44.0      149.5        6.1 
MinQuote    1619.6     184.5        62.9      187.2        6.4 
            1740.0     183.1        64.9      193.3        6.5 
   @Duty    2405.0     175.0        73.0      227.2        7.4 
            2610.0     172.3        74.5      237.7        7.8 
120%Duty    2886.0     168.4        76.0      251.9        8.4 
    @BEP    3239.2     162.9        76.9      270.3        9.4 
            3480.0     158.9        77.0      282.9       10.3 
MaxQuote    4355.5     141.4        73.5      330.0       14.4 
  
*WARNING* System NPSH was not provided! Some pump checks 
            can not calculated or may be inaccurate! 
Slysel pump performance data is based on the best available information for each 
pump. Where performance guarantees are required, contact your GIW representative. 
  
* Note: Pump Solids Effect is based on a Settling Slurry 
-------------------------------------------------------------------------------- 
Flow      :   2405.  GPM     Fluid  S.G. 0.982    Pump Service Class    :     1  
Head      :   175.0  ft      Slurry S.G. 1.560    Abrasivity Correction :   0.6 
Throughput:   530.1 tons/hr  Solids S.G. 2.860    D50 (microns)         :    74. 
Large particles (>2300 microns): Semi-Rounded     D85 (microns)         :   208. 
% fines <74 microns:  0.0    Miller (G75)  34.    Largest Solid(microns):  6000. 
Fluid pH  :     6.7          Temp (F)    150.0    Viscosity(lbf-s/ft^2) .0000091 
Chlorides :      0. (ppm) 
-------------------------------------------------------------------------------- 
  
Motor Power (HP) =  300. 
Pump Power (mechanical evaluation) (HP) =  227. 
Impeller End Radial Loads (lbf) =   -4349. 
Drive End Radial Loads (lbf) =    1936. 
Thrust Loads (lbf) =   10041. 
  
Drive End Radial Loads are based on a belt driven arrangement. 
  
Impeller End Bearing with C (lbf) =  191000.   L10 life (khrs) >200 
 Drive  End  Bearing with C (lbf) =  354000.   L10 life (khrs) >200 
Hydraulic Institute recommended minimum L10 Bearing Life for this duty is   17.5 (khrs) 
  
Pump Assembly's Gross Weight is    3776. lb 
  
Impeller Material        Impeller    Impeller    Impeller     Shaft 
     (28G)                (Dry)     (Carrier)    (Slurry)     (only) 
Inertia (lbm-ft^2)        231.9       256.0       270.3        13.4 
  
                                  Maximum Allowable Flange Loads 
Flange Location                    (lbf)                      (ft-lbs) 
                            Fx       Fy       Fz       Mx       My       Mz 
Discharge    8 (in)        3950.    3140.    4760.    4200.    4200.    6360. 
Suction     10 (in)        5330.    4420.    3520.    7130.    4700.    4700. 
 
COMMENTS:  

Metso Minerals/Constellation/WAPC
Brandon Shores
PO P162737
Metso Contract 72805/72806
Equip No:  0-205-P-452A1/B1/A2/B2
GIW Ser No 13012/13/14/15

227 hp = 169 kW

Содержание GIW LCC 100-400













































Отзывы: