KSB Calio-Therm S NC Скачать руководство пользователя

Страница: 26 / 32

8 Trouble-shooting

26 of 32

Calio-Therm S NC/NCV

8 Trouble-shooting

WARNING

Improper work to remedy faults

Risk of injury!

▷

For any work performed to remedy faults, observe the relevant information
given in this operating manual and/or in the product literature provided by the
accessories manufacturer.

If problems occur that are not described in the following table, consultation with the

KSB

customer service is required.

Pump is running, but does not deliver

Pump does not start up or pump running irregularly

Pump running but not delivering water

Noises during pump operation

Table 9:

Trouble-shooting

A B C D Possible cause

Remedy

✘

- Pump not connected to power supply

Check the power supply and fuses or
reset the voltage (interrupt and re-establish
power supply).

✘

- Pump blocked (e.g. due to contamination)

(

Section 7, Page 24)

✘

- Defective motor

Replace the pump.

✘

- Impurities in the pump

See section on maintenance.

✘

- Air in the system

Vent the system and the pump.

✘

- Gate valve closed

Open the gate valve.

✘

Excessive pump power output

Select a lower speed level.

✘

System pressure too low

Increase the system pressure by filling more water
into the boiler.

✘

Air in the system

Vent the pump and piping.

Release pump pressure before attempting to remedy faults on parts which are subjected to pressure.

Содержание Calio-Therm S NC

































Результаты поиска

Содержание Calio-Therm S NC

Отзывы:

Похожие инструкции для Calio-Therm S NC

Бренды по названию

Популярные бренды

KSB Calio-Therm S NC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Calio-Therm S NC

Отзывы:

Похожие инструкции для Calio-Therm S NC

Бренды по названию

Популярные бренды