background image

5 Installation at Site

16 of 32

Calio-Therm S NC/NCV

CAUTION

Air entering the pump

Damage to vertically installed pump sets whose direction of flow is downwards!

Fit a vent valve at the highest point of the suction line.

NOTE

To prevent any impurities from collecting in the pump do not install the pump at
the lowest point of the system.

1.

The circulator is usually installed in the piping directly upstream of the drinking
water storage tank. The water is pumped from the last tapping point via the
circulation line back to the storage tank.

2.

Install a lift check valve on the pump's discharge side. It prevents backflow
through the pump when the tap is opened.

3.

A shut-off valve is installed on the pump's suction side to facilitate maintenance. 
Calio-Therm S NCV comes with a lift check valve and a shut-off option integrated
in the lower pump section.

4.

Install the pump with the pump shaft in a horizontal position. Connect the
piping without transmitting any stresses and strains. 
An arrow on the pump casing indicates the direction of flow.

CAUTION

Heat building up at motor housing and pump casing

Pump overheating!

Never insulate the motor and electronic system housings.

5.4 Connecting the piping

 WARNING

Impermissible loads acting on the pump nozzles

Risk of burns by leakage of hot fluids!

Do not use the pump as an anchorage point for the piping.

Anchor the pipes in close proximity to the pump and connect them without
transmitting any stresses or strains.

Take appropriate measures to compensate for thermal expansion of the piping.

CAUTION

Contamination/dirt in the piping

Damage to the pump!

Flush the piping prior to commissioning or replacing the pump. Remove any
foreign matter.

Содержание Calio-Therm S NC

































Отзывы: