Krone Swadro 700 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 64

Krone Swadro 700 Скачать руководство пользователя страница 59

A - 1

Appendix

KS-0-096

3

5

1

2

4

6

A1.3 Installing the swath rubber

The swath rubber is mounted between the swather disks,
below the longitudinal frame. The angle rail (5) is mounted
on the machine ex-works.

Reinforcement (1) (BD 3 x 40 x 540; 4 pieces)
Steel bar (2) (Rd 20 x 595)
Swath blanket (3)
Steel strip (4) (Bd 2 x 30 x 1065; 2 pieces)
Angle strip (5)
Bolts (M 6 x 25)
Washer (6.4 x 18 x 1.6)
Self locking nut (NM 6)
Bolts (M 10 x 50)
Self locking nut (NM 10)
Protective sleeve (6) (PVC 40 x 5 x 100; 4 pieces)

Slide protective sleeve (6) onto reinforcement (1) and
insert in the pockets of the swath blanket (3) with the steel
bar (2). Screw the swath blanket onto the angle rail (5) with
the steel strip (4).
Screw steel bar (2) between the angle rail and the clip. Just
tighten the fixing bolt so that the steel bar can still freely
swing.

A1 Appendix to the operating manual

Assembly instructions (initial assembly)

A1.1 Preparations

• It is essential that the PTO shaft is switched off for all care, maintenance, repair and

assembly work on the rotary swather.

• Shut down the engine and remove the ignition key.
• Secure tractor and rotary swather against rolling away!

Machine may only be driven in the ready
for operation condition with wheels in
outer position. –
Danger of tipping over!

A1.2 Changing wheels on the

chassis

Attach the implement to the tractor, dismount wheels with
axle bolt and mount in outer position.

SW700039

800 Nm

800 Nm

Use only suitable lifting and installing
equipment!

«
...
57
58
59
60
61
...
»

Содержание Swadro 700

































































Отзывы:

Нет отзывов