Krone Swadro 700 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 64

Krone Swadro 700 Скачать руководство пользователя страница 30

IV - 2

Handling the swather when in use

4.3 Converting from transport to

working position

Before lowering the swather disk, make
sure that the lateral guard bars (1) are
turned inwards and no-one is within the
slewing range of the swather disks!

Do not run the swather disks in the
transport position or with retracted
guard bar!

Insert switch cock for the hydr. actuation of the swather
in the holder on the tractor.
Turn switch cock to central position (see adjacent.
graphic). Release the lock by actuating the tractor
hydraulics (lift). Release the lock actuating cable and
hold in place and slowly lower the swather disks by
actuating the hydraulics (lower). Release the actuating
cable again.

Electrical operation device

• Switch on operation device (0 > 1)
• Move Switch (5) to the central position

4.3.3 Lowering the rotor arms – electrically

(optional)

•

Operate single acting control valve on the tractor and
apply pressure to the hydraulic cylinders. This will
release the lock (1).

• Unlock the lock (1) by pulling the actuating cable (2).

Keep cable under tension.

• Use the control valve to slowly lower the outer rotor

until the wheels are on the ground.

• Release the actuating cable (2).

4.3.1 Lowering the rotor arms –

mechanically

During work operation, leave the
control valve in „Lower“ position.

SW700008

2

1

SW700005

4

3

2

1

5

K S 5 6 8 0 0 1

1

4.3.2 Lowering the rotor arms – hydraulic

single-rotor lifting system

«
...
28
29
30
31
32
...
»

Содержание Swadro 700

































































Отзывы:

Нет отзывов