Krone Swadro 700 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 64

Krone Swadro 700 Скачать руководство пользователя страница 29

IV - 1

Handling the swather when in use

4

Handling the swather
when in use

4.1 Mounting on the tractor

As described in Point 3.3, attach the swather to the
tractor, couple the universal drive shaft and secure.

• When attaching the rotary swather

make sure that no-one remains
between the implement and the
tractor.

• No-one may remain in the slewing

range of the swather disk arms!

The swather disks are secured against overloading by
so-called star-ratchet couplings. These star-ratchets (1)
are located on the lateral take-off shafts of the distributor
gearbox under the swather frame at the lateral swather
disk drives.

In the event of overloading, they produce a scraping
noise. They transmit the applied torque in pulses.
In order to prevent premature wear on the overload
protection feature, switch off the universal drive shaft
immediately, if the star ratchets respond during
overloading.

The overload protection feature may
not be adjusted. The guarantee is
canceled if overload protection devices
other than those provided ex-works are
used!

4.2 Overload protection feature

SW700022

1

«
...
27
28
29
30
31
...
»

Содержание Swadro 700

































































Отзывы:

Нет отзывов