Krone Swadro 700 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 64

Krone Swadro 700 Скачать руководство пользователя страница 21

III - 1

Preparing for Operation

KS-0-03

KS-0-030

• Always turn off PTO shaft before carrying out servicing, maintenance, repair or assembly work

on the rotary swather. Shut down the engine and remove the ignition key. Secure tractor and
rotary swather against rolling away!

• The maximum drive speed is 540 r.p.m.
• Actuating components such as ropes, drawing cables and hydraulic hoses as well as electrical

cables should be laid in such a way that they cannot be activated unintentionally or come into
contact with the tractor wheels. Risk of accidents!

• No-one may remain between the tractor and the rotary swather during raising and lowering

operations or below the raised swather arms. Extreme risk of injury!

• Before switching on the PTO shaft, ensure that there is no-one in the danger area around the

rotary swather. Risk of accidents!

• Check that the protective devices are fitted in accordance with the guidelines for operation and

for using public highways!
Check that the lighting is functioning properly.

• The operating personnel may not leave the tractor during operation!

Ensure other persons leave the danger area!

3

General preparation for use

3.1 Special safety instructions

Put the operation device to the position where the
possibility of unintentional raising or lowering is
excluded, before attaching and removing implements at
the three-point linkage!
Special care should be taken when coupling/uncoupling
implements to/from the tractor!
Risk of crushing and cutting injuries in the vicinity of the
three-point linkage!

3.2 Preparations on the tractor

• The tractor lower link arms should

always be set so that the lifting points
for the lower link arms are always the
same distance from the ground. The
lower link arms should be fixed by
limiting chains or rods so that the
implement cannot swing to the side
during transport or when working.

3.2.1 Lifting device on the tractor (three-point linkage)

The swather is equipped with category I and II coupling
lugs for the three-point hydraulics.

«
...
19
20
21
22
23
...
»

Содержание Swadro 700

































































Отзывы:

Нет отзывов