KROMBACH TUFSEAT Performance Series Скачать руководство пользователя страница 9

Страница: 9 / 28

www.cranecpe.com

Stem Seal Adjustment

KFO1156: HIGH TEMPERATURE TRIM

KFO1176: STANDARD TRIM

STEM SEAL ADJUSTMENT (Threaded Packing Gland)
Sizes: 1/2”-2” Cl.150 & 300, 3” Cl.150, DN15-DN50 PN10-
PN40, DN80 PN10-PN16 (1156, 1176)

To adjust for leakage along the valve stem, turn the Threaded
Packing Gland (#8) clockwise in approximately 1/3- turn
increments to compress the packing (#13). Use torques from
following table.

Note:

If a tight seal cannot be obtained, continue with the

instructions for valve repair.

Valve Size

Pressure Class

Threaded

Packing

Gland size

Threaded Packing Gland Torque

KFO1176

KFO1156

NPS

Class

metric

(Nm)

(in-lbs)

(Nm)

(in-lbs)

½”

DN15

#150 & #300

10-40

M30

116

1026

116

1026

¾”

DN20

#150 & #300

10-40

M30

116

1026

116

1026

1”

DN25

#150 & #300

10-40

M30

116

1026

116

1026

1 ½”

DN40

#150 & #300

10-40

M36

224

1982

224

1982

2”

DN50

#150

10-16

M36

224

1982

224

1982

2”

DN50

#300

25-40

M48

390

3452

390

3452

3”

DN80

#150

10-16

M48

390

3452

390

3452

Содержание TUFSEAT Performance Series





























Результаты поиска

Содержание TUFSEAT Performance Series

Отзывы:

Бренды по названию

Популярные бренды

KROMBACH TUFSEAT Performance Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание TUFSEAT Performance Series

Отзывы:

Бренды по названию

Популярные бренды