manualshive.com logo in svg

KROMBACH TUFSEAT Performance Series, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
KROMBACH TUFSEAT Performance Series Скачать руководство пользователя страница 17

17

www.cranecpe.com

                  

     

18. Insert the other seal ring (#40) over seat "A" (#6) and insert 
the two together into the body (#1) and over the "S" ring (#42). 
Apply grease to the sealing surfaces of the seat (#6). Apply 
pressure and axial force to pre-compress the seat seal accord-
ing to the values shown in table B and in the same manner as 
done on the cover (tail) side.

                  
                              
19.  Insert the ball (#3) into the body cavity (#1) with the port 
opening in the closed position (careful not to turn the ball 180 
degrees when opening and closing so that it stays as shown in 
the assembly drawing in accordance to ISO 5211).

                  
                      

 

       

  

 

20. Install spiral wound body gasket (5) in the groove 
of the body. 
          

                  

              

 

                                   

 

  

 

21.  Join the body (#1) and tail (#2), (lettering on the halves
face the same direction). install and tighten the body stud
nuts in the crossing pattern shown in Figure 7.

                   

Assembly of KFO-1176 Standard Trim Floating Ball Valve

Содержание TUFSEAT Performance Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды