KROMBACH TUFSEAT Performance Series Скачать руководство пользователя страница 20

Страница: 20 / 28

www.cranecpe.com

Assembly of KFO-1156 High Temperature Trim Floating Ball Valve

6. Apply "Castrol Optimol paste TA" on the screws and insert
them into the packing gland. Slightly pre-tighten them by
hand.

7. Compress the packings to the assembly compression;
Tighten the screws incrementally to the torque specified on
the table from Page 9 or 10.

8. Rotate the stem 5 times
NOTE: Always cycle in COUNTER-clock direction to open the
ball, and in clockwise direction to close the ball.

9. Remove the packing gland and the gland tube.

10. Repeat steps 4, 5, 6, 7 & 8, to get the stack of 8 packing
rings; alternate 4 Graphite packing rings (thick) & 4 Diffusion
barrier rings (thin).

11. Install the Threaded

Packing Gland (#8) over the valve

stem:

11.1 Threaded packing gland sizes: 1/2”-2” Cl.150 & 300, 3”
Cl.150, DN15-50 PN10-40 & DN80 PN10-16.

11.1.1 Rotate the press nut (#8) clockwise until it is lightly
compressing the packing (#13).
Note: Care must be taken to not cross-thread the press nut
(#8) and the body (#1).

Seat Assembly of KFO 1156 (High Temperature Trim)

12. Insert wiper ring (#15) into the body part (#1) & gently
push it into body groove.

Figure 9

Содержание TUFSEAT Performance Series





























Результаты поиска

Содержание TUFSEAT Performance Series

Отзывы:

Бренды по названию

Популярные бренды

KROMBACH TUFSEAT Performance Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание TUFSEAT Performance Series

Отзывы:

Бренды по названию

Популярные бренды