Kramer TP-594Rxr Скачать руководство пользователя

Страница: 47 / 67

Kramer Electronics Ltd.

TP-594Txr, TP-594Rxr

– Firmware Upgrade

Firmware Upgrade

The latest firmware version can be downloaded from the Kramer Web site at

www.kramerav.com/downloads/TP-594Rxr

www.kramerav.com/downloads/TP-594Txr

You can upgrade the firmware on

TP-594Txr

and

TP-594Rxr

(separately) in any of the

following methods:

•

The device embedded web pages (see

Upgrading the Firmware

on page

•

Using the Kramer

K-UPLOAD

software to upgrade the firmware via the

TP-594Txr

TP-594Rxr

PROG USB port

, via the CONTROL RS-232 port

or via the

CONTROL Ethernet port

The latest version of

K-UPLOAD

and installation instructions can be downloaded

from our website at:

www.kramerav.com/support/product_downloads.asp

•

Directly using a memory stick (see

Upgrading the Firmware Using a Memory Stick

on page

Upgrading the Firmware Using a Memory Stick

You can upgrade

TP-594Txr

TP-594Rxr

via the USB port

on the rear panel.

To upgrade the firmware via the USB port:

1. Download the firmware Bin. file and copy it to the root folder of a USB flash drive

memory stick, formatted with FAT32 system.

2. Connect your PC to the device.

3. Connect the USB flash drive to the device.

4. Send the X-UPGRADE command to the device (via RS-232 or Ethernet):

▪

For

TP-594Txr

: “#X-UPGRADE IN.USB_PORT.1,TP-594TXR_All*.Bin”.

▪

For

TP-594Rxr

: “#X-UPGRADE IN.USB_PORT.1,TP-594RXR_All*.Bin”.

5. Check that the firmware was updated in the lower left side of the device Navigation pane

(see

Browsing the Web Pages

on page

DRAFT

Содержание TP-594Rxr




































































Результаты поиска

Содержание TP-594Rxr

Отзывы:

Похожие инструкции для TP-594Rxr

Бренды по названию

Популярные бренды

Kramer TP-594Rxr, Руководство пользователя

Результаты поиска

Содержание TP-594Rxr

Отзывы:

Похожие инструкции для TP-594Rxr

Бренды по названию

Популярные бренды