manualshive.com logo in svg

KRAL CGF, Руководство по эксплуатации

Поделиться
Скачать
KRAL CGF Скачать руководство пользователя страница 63

17 Appendix

17.2 Tightening torques for screw plugs with thread measured in inches and elastomer seal

17.2 Tightening torques for screw plugs with thread measured in inches and elastomer

seal

Notice

In the case of galvanised screw plugs and screw plugs made of stainless steel the inner thread and
outer thread have to be greased thorough before mounting in order to prevent threads from seizing.

Tightening torque [Nm]

Thread

Galv stainless steel

G 1/8"

13.0

G 1/4"

30.0

G 3/8"

60.0

G 1/2"

80.0

G 3/4"

120

G 1"

200

G 1 1/4"

400

G 1 1/2"

450

Tab. 24: Tightening torques, thread measured in inches

17.3 Contents of the Declaration of Conformity

The products described in these instructions are machinery in the sense of the Directive 2006/42/EC.
The original of the EC Declaration of Conformity is enclosed with the machinery at delivery.

The machinery fulfils all the relevant provisions of the following directives:

Number

Name

Remark

2006/42/EC

Machinery Directive

–

2014/68/EU

Pressure Equipment Directive

–

2014/30/EU

Directive on Electromagnetic
Compatibility

Only for machinery with electrical
components

2014/35/EU

Low Voltage Directive

Only for machinery with electrical
components

2014/34/EU

Directive on Use in Potentially
Explosive Areas (ATEX)

Only for machinery in ATEX version

Tab. 25: Directives observed

Operating instructions

OIC 18en-GB Edition 2020-01

63

Содержание CGF

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды