manualshive.com logo in svg

KRAL CGF, Руководство по эксплуатации

Поделиться
Скачать
KRAL CGF Скачать руководство пользователя страница 18

8 Installation, removal

8.1 Dangers during installation

8 Installation, removal

8.1 Dangers during installation

The following safety instructions must be observed strictly:

o

Have all work carried out only by authorized qualified personnel.

o

Before installation ensure that the operating limits, NPSH values and ambient conditions are ob-
served.

o

Observe the tightening torques 

Ä

 Appendix, Page 62.

o

Ensure that all the components can be accessed and that maintenance work can be carried out
easily.

8.2 Dangers during removal

The following safety instructions must be observed strictly:

o

Have all work carried out only by authorized qualified personnel.

o

Before beginning work, let the pump unit cool down to the ambient temperature.

o

Collect any discharging pumped liquid safely and dispose of it in an environmentally compatible
manner in accordance with the applicable local regulations.

o

Ensure that the collection tank for discharging pumped liquids is sufficiently large.

8.3 Installing the pump

The pumps can be operated in horizontal and vertical installation position.

Notice

Soiling in the pipe system impair the service life of the pump. If the pipe system is flushed using the
pump during the initial commissioning, an additional commissioning filter has to be installed temporarily
before the pump at the system (mesh width: 0.02 mm).

Personnel qualification:

o

Transport personnel

o

Fitter

Personal protective equipment:

o

Work clothing

o

Protective helmet

o

Protective gloves

o

Safety boots

Aids:

o

Mobile crane, forklift, hoisting equipment

 WARNING

Risk of injury and damage to equipment through falling and toppling parts.

► Only fasten the pump on a stable load-bearing underground or stable load-bearing load support.

► Ensure that fastening elements and pipings are fastened sufficiently.

ATTENTION

Damage to motor through emitted pumped liquid.

► Do not install the pump above the motor.

ATTENTION

Damage to device through impurity in the pipe system.

► During welding work attach protective covers in front of the connecting flanges.

► Ensure when welding that welding beads and abrasive dust cannot get into the pipe system and

the pump.

► Ensure that a commissioning filter is installed when the pipe system is flushed and cleaned using

the pump.

18

OIC 18en-GB Edition 2020-01

Operating instructions

Содержание CGF

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды