KRAL CGF Скачать руководство пользователя страница 25

Страница: 25 / 64

10 Operation

10.2 Commissioning

Compare the direction of rotation of the fan impeller with the arrow indicating the direction of

rotation

If the directions do not match, swap the two electrical connection phases. Repeat Steps 1 and 2.

10.2.4

Commissioning the pump

Personnel qualification:

Fitter

Electrician

Personal protective equipment:

Work clothing

Face protection

Protective gloves

Safety boots

Aids:

Collection tank

DANGER

Risk of death resulting from bursting components and emitted pumped liquid.

As a result of impermissibly high pressure, components can burst with high energy, for example
through the pressure-side pipe system being shut off.

► Wear personal protective equipment during all the work.

► Before carrying out commissioning ensure that a safety valve is installed in the pressure-side pipe

system at the system end.

WARNING

Risk of injury through emitted pumped liquid.

Pumped liquids can be hot, poisonous, combustible and caustic.

► Wear personal protective clothing during all the work. Ensure face protection.

► Collect any discharging pumped liquid safely and dispose of it in an environmentally compatible

manner in accordance with the applicable local regulations.

WARNING

Hot surface.

Touching of uninsulated hot surfaces results in burns.

► Insulate components and pipings in which hot liquids (> 60 °C) flow before commissioning.

WARNING

Danger of injury through rotating parts.

► Ensure that the coupling protection is mounted.

ATTENTION

Dry running can damage pump equipment.

► Ensure that the pump and the connected pipe system are filled properly.

► If the pump does not deliver after 10 – 15 seconds, abort commissioning.

Operating instructions

OIC 18en-GB Edition 2020-01

Содержание CGF

































































Результаты поиска

Содержание CGF

Отзывы:

Бренды по названию

Популярные бренды

KRAL CGF, Руководство по эксплуатации

Результаты поиска

Содержание CGF

Отзывы:

Бренды по названию

Популярные бренды