manualshive.com logo in svg

KRAL BEM 300 Series, Руководство по эксплуатации

Поделиться
Скачать
KRAL BEM 300 Series Скачать руководство пользователя страница 14

14

OIE 15en  Edition 2019-12 HW 2.0/SW 2.0 

Operating Instructions

Removal

Installation and removal

Prerequisite:

□

All cables have been cut to length and connected

Aids

□

KRAL tool set

1. Mount the universal mount 

2

 on the mounting set 

3

.

2. Mount the mounting set including universal mount to the pipe/volumeter.
3. Slide the electronic unit into the universal mount.
4. Fasten the electronic unit using the supplied screws, washers and wedge lock washers.
The electronic unit is ready to operate after the power supply has been switched on.

Removal

Prerequisite:

□

Power supply switched off

Aids:

□

KRAL tool set

□

Terminal tool

Removing the electronic unit from the control cabinet

1. Disconnect all the wires
2. Unscrew the connecting screws between the front and sealing frames.
3. Pull off the sealing frame to the rear.
4. Pull the electronic unit with front frame from the front out of the control cabinet.
5. Press the front frame to the rear and pull it off the electronic unit.

Removing the electronic unit from the wall

1. Unscrew the connecting screws between the electronic unit and the universal mount.
2. Slide the electronic unit out of the universal mount.

Removing the electronic unit from the pipe/volumeter

1. Unscrew the connecting screws between the electronic unit and the universal mount.
2. Slide the electronic unit out of the universal mount.

Fig. 5

Fixing kit for pipe mounting / 
KRAL Volumeter OMG series

Fig. 6

Fixing kit for KRAL Volumeter OME 
series

1

Electronic unit

2

Universal mount

3

Fixing kit for pipe mounting/OMG

1

Electronic unit

2

Universal mount

3

Fixing kit OME

1

2

3

1

2

3

Содержание BEM 300 Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды