KRAL BEM 300 Series Скачать руководство пользователя

Страница: 13 / 48

Operating Instructions

OIE 15en Edition 2019-12 HW 2.0/SW 2.0

Installation

Installation and removal

1. Create a control cabinet section, see Fig. 3, page 12.
2. When the space is limited, remove the housing cover

and gasket with cable entries

3. Slide the front frame

from behind onto the electronic unit

4. Place the electronic unit with the front frame from the front into the control cabinet section, see

Fig. 3, page 12.

5. Slide the sealing frame

from behind onto the electronic unit, whereby the sealing surface has to

point to the front.

6. Fasten the front frame and sealing frame using the 4 supplied screws and lock washers. Tighten the

screws carefully.
Tightening torque: 1 Nm

The electronic unit is ready for the connection of the cables.

Wall mounting

A universal mount, that is available as an accessory, is used for wall mounting see "Accessories moun-
ting", page 37.

Prerequisite:

□

Universal mount is mounted to the wall

□

All cables have been cut to length and connected

Aids

□

KRAL tool set

1. Slide the electronic unit

into the universal mount

2. Fasten the electronic unit using the supplied screws, washers and wedge lock washers.

The electronic unit is ready to operate after the power supply has been switched on.

Pipe mounting / mounting on volumeter

The electronic unit can be mounted to the pipe or on the volumeter by means of the universal mount and
the corresponding mounting set. The required mounting set is available as an accessory, see "Accesso-
ries mounting", page 37.

DANGER

Risk of death resulting from electric shock.

► Ensure that the power supply is disconnected.
► The electronic unit may only be connected by an authorized electrician.

Electronic unit

Universal mount

Fig. 4

Universal mount for wall mounting

Содержание BEM 300 Series

















































Результаты поиска

Содержание BEM 300 Series

Отзывы:

Похожие инструкции для BEM 300 Series

Бренды по названию

Популярные бренды

KRAL BEM 300 Series, Руководство по эксплуатации

Результаты поиска

Содержание BEM 300 Series

Отзывы:

Похожие инструкции для BEM 300 Series

Бренды по названию

Популярные бренды