Kraft Werkzeuge 3906132917, Перевод с оригинального руководства пользователя

Страница: 16 / 32

16 16 GB
Before starting the equipment
Before you connect the equipment to the mains sup -
ply make sure that the data on the rating plate are
identical to the mains data.
•
Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
•
Install the compressor near the point of consump -
tion.
•
Avoid long air lines and supply lines (extension ca -
bles).
•
Make sure that the intake air is dry and dustfree.
•
Do not install the compressor in a damp or wet
room.
•
The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature
from +5 °C to 40 °C). There must be no dust, acids,
vapors, explosive gases or inflammable gases in the
room.
•
The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
Attachment and operation
n
Important!
You must fully assemble the appliance before
using it for the first time!
Mains connection
• The compressor can be connected to any 220 -
240-240 V~ 50 Hz shock-proof socket which is pro-
tected by a 16 A fuse.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
(see the rating plate).
• Long supply cables, extensions, cable reels etc.
cause a drop in voltage and can impede motor
start-up.
• At low temperatures below +5°C, sluggishness
may make starting difficult or impossible.
ON/OFF switch (fig. 1)
• To switch on the compressor, press the ON/OFF
switch (2) on position I.
• To switch off the compressor, press the ON/OFF
switch (2) on position 0.
Establishing connections (fig. 3, 4)
m
Attention! Switch the device off for this.
When doing so, hold the coupling firmly in order to
avoid injuries due to the hose springing back.
•
Connect the fitting of your compressed air tool to
the compressed air hose (5) of the compressor.
• To disconnect this coupling again, pull the quick-
coupling (4) back at the compressed air hose (5).
• Do not store or eat food and drink in the
work area. Paint vapors are harmful to
your health.
• The work area must exceed 30 m3 and
sufficient ventilation must be ensured
during spraying and drying. Do not spray
against the wind. Always adhere to the
regulations of the local police authority
when spraying combustible or hazardous
materials.
• Do not process media such as white spirit,
butyl alcohol and methylene chloride with
the PVC pressure hose.These media will
destroy the pressure hose.
Do not lose these safety instructions
Technical data
Mains connection 220 - 240 V~ 50 Hz
Motor rating W
max. 1100
Operating mode S3 15%
Compressor speed min
-1
3750 min
-1
Operating pressure approx. 8 bar
Theoretical intake
capacity (l/min)
approx. 180
Sound power level L
WA
96 dB(A)
Uncertainty K
WA
1.9 dB
Sound Pressure Level L
pa
74 dB(A)
Protection type IP20
Protection class II
Weight of the unit in kg 5.5
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Residual risks
Comply with the stipulated maintenance and safety
instructions in the operating instructions.
Remain attentive at all times when working and keep
third parties at a safe distance from your work area.
Even when the device is being used properly, there
will always be certain residual hazards that cannot
be completely ruled out. The following potential haz-
ards can arise due to the type and design of the
device:
•
Unintentional starting up of the product.
•
Damage to hearing if the stipulated hearing pro-
tection is not worn.
•
Dirt particles, dust etc. can get into the eyes or
face despite wearing safety goggles.
•
Inhaling swirled up particles.