Kozy-World KWN111 Скачать руководство пользователя страница 15

1 5

TROUBLESHOOTING

Continued

  WARNING: If you smell gas

Shut  off  gas  supply.

Do  not try  to  light  any  appliance.

Do  not touch  any  electrical  switch;  do not use  any  phone  in  your building.

Immediately  call  your  gas  supplier  from  a  neighbor’s  phone.  Follow  the  gas

        supplier’s  instructions.

If  you  cannot  reach  your  gas  supplier,  call  the  fire  department.

IMPORTANT:  Operating  heater  where  impurities  in  air  exist  may  create odors. Clean-

ing supplies,  paint,  paint  remover,  cigarette  smoke,  cements  and  glues,  new  carpet  or

textiles,  etc.,  create  fumes. These fumes may mix  with  combustion  air  and  create odors.

REMEDY

1.     Ventilate room. Stop using odor
        causing products while heater
        is running.

2.     Locate and correct  all  leaks(see
        Checking     Gas     Connections,
        page 10).

1.    Open  window  and/or  door   for
        ventilation.
2.     Contact        local       natural    gas
       company.
3.    Clean  ODS/pilot (see  Cleaning
        page  12).

1.     Locate  and  correct  all  leak s(see
       Checking     Gas    Connections,
        page  10).
2.    Replace  control  valve.

1.    Take    apart    gas   tubing   and
        remove  foreign  matter.
2.     Locate    and   correct   all   leaks
      (see  Checking  Gas Connections,
       page 10).

1.     Refer  to  Air for Combustion and
        Ventilation Requirements,  page
         4.

POSSIBLE CAUSE

1.    Heater  is   burning    vapors    from
       paint,    hair    spray,   glues,   etc.
     (See  IMPORTANT  statement
      above).
2 .   G a s     l e a k .     S e e     Wa r n i n g
      Statement at top of page.

1.     Not enough  fresh  air  is  available.

2.    Low   line  pressure.

3.  ODS/pilot  is  partially  clogged.

1.  Gas   leak.   See   Warning
      Statement  at  top  of  page.

2.   Control   valve  is  defective.

1.    Foreign  matter  between  control
       valve  and  burner.
2.    Gas         leak.        See      Warning
      Statement  at  top  of  page.

1.    Not   enough  combustion/ventilation
      air.

OBSERVED  PROBLEM

Heater  produces  unwanted  odors.

Heater  shuts  off  in  use (ODS operates).

Gas  odor  even  when  control  knob  is
in   OFF  position.

Gas  odor  exists during  combustion.

Moisture/condensation     noticed     on
windows.

Содержание KWN111



















Отзывы: