kozy heat PRC-36 Скачать руководство пользователя

Страница: 17 / 38

Page 16

MODEL #PRC-36 ONLY: OPTIONAL FAN INSTALLATION INSTRUCTIONS

NSTALLATION OF THIS FAN SHOULD BE DONE ONLY BY A QUALIFIED INSTALLER

IMPORTANT: If a fan is going to be installed, it is easier to complete before the millivolt board is connected to the gas line.

The wiring must be done prior to enclosing the sides of the unit. An electrical box & romex connector are pre-installed

on a removable panel on the right side of the fireplace. A receptacle / speed control assembly and (3) wire nuts are

included in the fireplace components packet.

This optional fan kit, part #TRF-028, includes:

Right & left fan assemblies with thermostatic control switch
Components package: Installation instructions

NOTE:

Code approved line voltage wiring 14 gauge or better must be used when wiring this assembly. Refer to your local

electrical codes for specific requirements in your area.

WARNING: This appliance is equipped with a three-prong (grounding) plug for protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

Figure 14

Содержание PRC-36







































Результаты поиска

Содержание PRC-36

Отзывы:

Похожие инструкции для PRC-36

Бренды по названию

Популярные бренды

kozy heat PRC-36, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PRC-36

Отзывы:

Похожие инструкции для PRC-36

Бренды по названию

Популярные бренды