kozy heat BIR-20-L Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 50

kozy heat BIR-20-L Скачать руководство пользователя страница 30

30

FIREPLACE SETUP

Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces

#BIR-20-L R.5 June 2020

7.4 Control Board Removal and Installation

WARNING: If burner and/or pilot have been burning,

use appropriate protection to avoid burns or damage

to personal property before removing any components.

DO NOT OPERATE THIS APPLIANCE WITHOUT THE SEALING GASKET

(LOCATED UNDER THE CONTROL BOARD) IN PLACE. IF GASKETING IS

DAMAGED, IT MUST BE REPLACED.
CAUTION: Check all connections for leaks with soapy water, whether

field or factory made.

7.4.1 Control Board Removal

1. Disconnect electrical power.
2. Locate the manual valve installed by your qualified service

technician.

3.  Turn the manual valve clockwise to the OFF position.
4.  Remove the safety barrier and glass frame assembly.
5.  Remove logs.
6.  Remove the back log plate (2) screws.
7.  Remove (2) screws on each side of the back burner. Slide the

burner tube venturi to the right to release from the burner

orifice.

8. Remove the front burner from the firebox (4) screws.
9. Remove and save (10) screws securing the control board. Lift

the control board and disconnect the main burner on/off rocker

switch wires. Lift the control module out of the firebox, being

careful not to damage sealing gasket underneath.

7.4.2 Control Board Installation

1. Place the control module in the firebox, aligning the holes in the

control board with the holes in the firebox bottom.

VERIFY SEALING GASKET IS IN PLACE.

2. Reconnect main burner on/off rocker switch wires.

3. Secure the control board to the firebox using (10) screws

previously removed.

4. Reinstall the front burner (4) screws, positioning the burner

venturi over the burner orifice.

5. Reinstall the back burner. Position the burner tube venturi over

the burner orifice. Secure with (2) screws.

6. Reinstall the back log plate (2) screws.

7.  Reinstall log set.
8.  Reinstall the glass frame assembly and safety barrier.
9.  Turn the manual valve counterclockwise to the ON position.
10.  Reconnect electrical power.
11.  Verify proper log placement, operation of fireplace, and any

electrical components.

Figure 7.5, Control Board Removal and Installation

Front Burner

Back Burner

Back Log Plate

«
...
28
29
30
31
32
...
»

Содержание BIR-20-L



















































Отзывы:

Нет отзывов