Korenix JetNet 5008G-P Series Скачать руководство пользователя | Manualshive

Страница: 57 / 96

background image

54

(for VLAN 2)
Display – Port Ingress
Rule (PVID, Ingress
Filtering, Acceptable
Frame Type)

Switch# show interface fa1
Interface fastethernet1
    Administrative Status : Enable
    Operating Status : Not Connected
Duplex : Auto
Speed : Auto
Flow Control :off
    Default Port VLAN ID: 2
    Ingress Filtering : Disabled
Acceptable Frame Type : All
    Port Security : Disabled
    Auto Negotiation : Enable
    Loopback Mode : None
STP Status: disabled
    Default CoS Value for untagged packets is 0.
Mdix mode is Auto.
Medium mode is Copper.

Display – Port Egress
Rule (Egress rule, IP
address, status)

Switch# show running-config
……
!
interface fastethernet1
  switchport access vlan 1
  switchport access vlan 3
  switchport trunk native vlan 2
…….
interface vlan1
  ip address 192.168.10.8/24
no shutdown

VLAN Configuration

Create VLAN (2)

Switch(config)# vlan 2
vlan 10 success

Switch(config)# interface vlan 2
Switch(config-if)#

Note: In CLI configuration, you should create a VLAN
interface first. Then you can start to add/remove ports.
Default status of the created VLAN is unused until you add
member ports to it.

Remove VLAN

Switch(config)# no vlan 2
no vlan success

Note: You can only remove the VLAN when the VLAN is in
unused mode.

VLAN Name

Switch(config)# vlan 2
vlan 2 has exists
Switch(config-vlan)# name v2

Switch(config-vlan)# no name

Note: Use no name to change the name to default name,
VLAN VID.

VLAN description

Switch(config)# interface vlan 2
Switch(config-if)#

«
...
55
56
57
58
59
...
»

Содержание JetNet 5008G-P Series

































































































Отзывы:

Нет отзывов

Похожие инструкции для JetNet 5008G-P Series

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: Ubiquiti Страницы: 20

Бренд: Idis Страницы: 17

IGS-5225-20T4C2X

Бренд: Planet Страницы: 16

Бренд: Avigilon Страницы: 12

Бренд: ENKHO Страницы: 48

Бренд: ActionTec Страницы: 87

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

RuggedNet 10G/Si

Бренд: OST Страницы: 8

Бренд: TRENDnet Страницы: 3

Бренд: AIC Страницы: 64

Бренд: Allied Telesis Страницы: 2

Бренд: HighPoint Страницы: 3

Бренд: Cabletron Systems Страницы: 54

Бренд: Billion Страницы: 121

Бренд: CYP Страницы: 16

Бренд: Thales Страницы: 470

Бренд: Advantek Networks Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды