Korenix JetNet 5008G-P Series Скачать руководство пользователя

Страница: 55 / 96

Static VLAN Configuration

You can see the created VLANs and specify the egress (outgoing) port rule to be

Untagged

Tagged

here.

Figure 4.5.2.3 Static VLAN Configuration table. You can see that new VLAN 3 is created.
VLAN name is test. Egress rules of the ports are not configured now.

Figure 4.5.2.4 Configure Egress rule of the ports.

: Not available

Untag

: Indicates that egress/outgoing frames are not VLAN tagged.

Tag

: Indicates that egress/outgoing frames are to be VLAN tagged.

Steps to configure Egress rules: Select the VLAN ID. Entry of the selected VLAN turns to
light blue. Assign Egress rule of the ports to

. Press

Apply

to apply the setting. If you

want to remove one VLAN, select the VLAN entry. Then press

Remove

button.

Содержание JetNet 5008G-P Series

































































































Результаты поиска

Содержание JetNet 5008G-P Series

Отзывы:

Похожие инструкции для JetNet 5008G-P Series

Бренды по названию

Популярные бренды

Korenix JetNet 5008G-P Series, Руководство пользователя

Результаты поиска

Содержание JetNet 5008G-P Series

Отзывы:

Похожие инструкции для JetNet 5008G-P Series

Бренды по названию

Популярные бренды