Korenix JetI/O 6510 Скачать руководство пользователя страница 32

Страница: 32 / 95

4.2 Block I/O OPC Server Utility

1. Go to “Start” -> “Program”, and then you can see the “Block IO Utility (Korenix) folder.

There are 2 utilities are installed, Block IO OPC Server and Block IO Utility.

2. Open the “Block IO OPC Server”.

3. Select “File -> New” to create new profile. Or select “File -> Open” to open profile you

saved.

4. Select “Add -> New Device”, the popup window “Driver Selection” will appear. (Only

appear in the first time you add new device). Click “Add” and type the driver name and
correct IP address. Click “OK” to next popup windows for Driver Selection. Use “Edit
-> Comm Setting” can modify the parameters.

Note: Different model should have different Driver Name. We recommend user adds
all the drivers for all the available models you connected first.

Содержание JetI/O 6510
































































































Результаты поиска

Содержание JetI/O 6510

Отзывы:

Бренды по названию

Популярные бренды

Korenix JetI/O 6510, Руководство пользователя

Результаты поиска

Содержание JetI/O 6510

Отзывы:

Бренды по названию

Популярные бренды