Korenix JetI/O 6510 Скачать руководство пользователя страница 26

Страница: 26 / 95

further assignments for those internal flags which will mirror the remote

internal flags on the corresponding remotely input module as defined on the

field of “Remote IP address”. It could support up to 8 rules assignment.

Press “Apply” to activate the new setting.

After completing all configurations for Peer-to-Peer I/O activity, click “Save”

button, all the mapping configurations will be flushed into flash memory on

the module. In order to extend the flash memory life, it is strongly

recommended that you should save all configurations together at one time

instead of saving individual setting many times. The indicator in the left of the

“Save” button shows the status of being flushed into flash memory. If there

was error occurred, the color become to red. Otherwise, the system will

automatically restart the module and prompt you to rescan the module on the

network again.

Содержание JetI/O 6510
































































































Результаты поиска

Содержание JetI/O 6510

Отзывы:

Бренды по названию

Популярные бренды

Korenix JetI/O 6510, Руководство пользователя

Результаты поиска

Содержание JetI/O 6510

Отзывы:

Бренды по названию

Популярные бренды