Korenix JetI/O 6510 Скачать руководство пользователя страница 19

Страница: 19 / 95

It should be noticed that the privilege setting is required to gain access to do

the further configuration options. When you install the I/O module in first time,

the default password is “admin”. You just need to click on “Login” button and

type the password of “Admin” on “password for entry” field. If you want to

make password changes, click “Change” button and then the dialog of “Chang

Password” prompts you to update the new password with up to six characters.

Note 1: The password protection is the new feature provided in firmware F206

and Utility V1.3 or later

Note 2: When you upgrade firmware from F204 to F206, the default password

is disabled, please change new password for your device.
Note 3: If you forget the password, you may need to reset the module via

‘Reset to default’ command, referred to section 2.2.6, to clear the password

and load factory defaults. This will result in the clear all the configuration

settings as you assigned.

Each module has its own page to display and configure the TCP/IP parameters.

If the function of DHCP is disabled, user can type the IP address, Gateway and

Subnet Mask information on the page. When everything is ok, user can push

Содержание JetI/O 6510
































































































Результаты поиска

Содержание JetI/O 6510

Отзывы:

Бренды по названию

Популярные бренды

Korenix JetI/O 6510, Руководство пользователя

Результаты поиска

Содержание JetI/O 6510

Отзывы:

Бренды по названию

Популярные бренды