SAFETY NOTES
TECHNICAL DATA
Thank you for choosing this product. The instructions provide directions to all of the important setup and handling steps.
We recommend you keep these instructions for future reference.
A. GENERAL
- Load capacity: max 15 kg*
- Proper assignment of setup crew (if needed we recommend 2 physically fit technicians)
- Keep unauthorized personnel away from the stand.
- Careful and attentive handling is required when adjusting the stand - due to the possibility of
-
pinching or wedging your hand.
- Moving the stand, particularly if the lights are attached, is not permitted (Could fall over,
-
component stress)
- Only to be used indoors
B. PRIOR TO USE
- Prior and after use the stand should undergo visual inspection,
-
to ensure that all components are there and in working order.
- Damaged stands may not be used i.e. it must be repaired by a qualified technician.
- Equipment and aids (e.g. Ladders) are to be inspected to ensure that they are in working order.
- Be sure that the surface will bear the load and is suitable and level.
C. STAND SETUP
- Please consider the information provided in the
SETUP INSTRUCTIONS
- The largest base circumference and maximum stability is achieved when
-
the tripod struts are horizontal
4
- Tighten the clamp screws - without the use of tools.
-
Manual strength is enough, overtightening can negatively affect the components.
- The desired height is also to be secured using the locking rings
9
.
D. DURING OPERATION
- Safety during operation is based on:
-
1.
FOLLOWING
the points listed here under
A - E
.
-
2.
MASTERING
the
LATERAL FORCES
(> DANGER OF THE STAND FALLING OVER).
-
2.
Lateral forces should be avoided at all costs. They occur in the case:
-
2.
a. the stand is tilted (uneven surface)
-
2.
b. the load bearing weight is not centered
-
2.
c. external shocks such as bumping into the stand, brushing into the stand, wind etc.
-
2.
NOTE:
Maintain safety distance, keep unauthorized persons away. Should the effectiveness
-
2.
of the measures not be guaranteed, (e.g. through the safety distance not being kept and
-
2.
not being checked) the installer should implement the following additional steps, e.g. rigging
E. DISASSEMBLY
- Let the light retract slowly and in a controlled fashion.
- First remove the light - then collapse the stand.
SET UP INSTRUCTIONS
SETTING UP
the 24645 Lighting Stand is very easy. All components are
preassembled, and only need to be placed in the proper position.
1
Loosen the clamping screw of the triangular clamp/bracket a bit.
2
Expand the legs...
3
... until the triangular clamp/bracket clicks into place.
4
The tripod struts are now positioned in a horizontal position.
5
Re-tighten the clamping screw.
TIGHTEN Screw
6
The 3-piece tube combination combines:
6a
lights at great heights (min. 1430 mm - max. 3100 mm) with
6b
a compact and transport-friendly package size (1175mm).
7
The upper tube end is equipped with a M10 screw socket, commonly used for light stands
8
In addition, the end tube (ø 30 mm) is equipped with a simple ø 35 mm adapter sleeve
8
that is easy to screw on and unscrew
9
The clamping of the tubes is done using two mechanisms. Each clamping bracket is
9
supplemented with a locking ring.
CHECK, MAINTENANCE, CLEANING
- Careful use of the stand maintains the use of the telescope and the load bearing functionality
-
of the stand, as well as the safety of the installation.
- Perform workstation maintenance only without the lighting being attached and watch for
-
possible risks (pinched fingers, impact, the stands falls over)
- To care for the product, use a damp cloth and a non-abrasive cleaning agent.
24645 Lighting stand
- Load capacity max. 15 kg*
- Variable height adjustment 3-piece tube combination
- Very easy to transport: Light-weight aluminum construction, small package dimensions (1175 mm)
- Height 1430-3100 mm; Bottom tube; ø 30 mm (Adapter ø 35 mm), M10-Screw socket; Base ø 1110 mm, Weight: 3.4 kg
Material
Base-, extension-, foot-tubes: Aluminum
Struts: Steel
Brackets: Polyamide (PA)
End caps: TPE
Load capacity
max. 15 kg*
Dimensions
Height: 1430-3100 mm (max. base circumference)
max. base circumference diameter 1153 mm
Extension tube: ø 30 mm (with adapter sleeve 35 mm)
Weight: net 3.4 kg; gross 4.1 kg
Pack size
W x D x H: 122 x 142 x 1175 mm
Box
W x D x H: 130 x 120 x 1185 mm
Accessories
(optional)
Carrying Case 21311 (for one or two 24645)
suitable for the M10 screw socket:
- Crossbar 213/9, Connection sleeve 66350, TV pin 24516
suitable for the adapter sleeve ø 35 mm:
- Crossbars 21393 and 24622
Rigging 24613
= TIGHTEN Screw
= LOOSEN Screw
Upper
Clamping
Bracket
Lower
Clamping
Bracket
Box
Upper
Locking ring
Lower
Locking ring
* With centric loading, on a horizontal surface and without lateral forces (wind, shocks etc.)
