Konica Minolta Magicolor 5440 dl Скачать руководство пользователя

Страница: 141 / 164

Status, Error, and Service Messages

131

FUSER
NOT ATTACHED

The fuser unit is not
installed.

Contact Technical Sup-
port with the error infor-
mation.

MANUAL FEED TRAY
NOT INSTALLED

The manual feed tray
was specified with the
printer driver for print-
ing, but the manual
feed tray is not
installed.

Install the manual feed
tray.

MEDIA JAM
DUPLEX LOWER

Media has misfed in
the duplex option.

Locate and remove the
misfeed.

MEDIA JAM
DUPLEX UPPER

Media has misfed in
the duplex option.

MEDIA JAM
FUSER

Media has misfed
leaving the fuser
area.

MEDIA JAM
MANUAL FEED TRAY

Media has misfed in
the manual feed tray.

MEDIA JAM
TRANSFER ROLLER

Media has misfed in
the transfer roller
area. This type of
misfeed means that
the media did not
make it to the paper
exit area.

MEDIA JAM
TRAY

Media has misfed
while being pulled
from the specified
tray (

MEDIA JAM
UNDEFINED

A media misfeed
occurred because the
driver settings are
inconsistent.

After clearing the media
misfeed, check the
driver settings.

PUT MEDIA : M-TRAY
“MEDIA”

The media type set in
the printer driver is
different from the type
of media loaded into
the manual feed tray.

Load the correct media
type into the manual
feed tray.

This message...

means...

do this...

Содержание Magicolor 5440 dl





































































































































































Результаты поиска

Содержание Magicolor 5440 dl

Отзывы:

Похожие инструкции для Magicolor 5440 dl

Бренды по названию

Популярные бренды

Konica Minolta Magicolor 5440 dl, Руководство пользователя

Результаты поиска

Содержание Magicolor 5440 dl

Отзывы:

Похожие инструкции для Magicolor 5440 dl

Бренды по названию

Популярные бренды