Kongsberg M3 Sonar FLS Скачать руководство пользователя страница 6

Страница: 6 / 98

922-20297011/1.0

Ethernet cable .............................................................................................................. 45
Sonar Head - SEA CON MINK-10-CCPL:Power, Ethernet, 1PPS, and Sync ........... 46

Basic cable requirements ...................................................................................................... 47

SETTING TO WORK .................................................................... 51

Setting to work summary ...................................................................................................... 52
Making sure that the M3 Sonar FLS is ready for operational use ........................................ 53

Verifying that the operating power is correct .............................................................. 53
Verifying that all hardware is properly installed ......................................................... 54
Making sure that all M3 Sonar FLS system cables are properly connected ............... 55

Turning on the M3 Sonar FLS .............................................................................................. 57
Configuring the M3 Sonar FLS system for normal operation .............................................. 59

Setting the Sonar Processor to High Performance ...................................................... 60
Installing the M3 Sonar FLS software ........................................................................ 61
Defining the IP address on the Sonar Processor network adapter ............................... 62

Testing the operating functionality of the M3 Sonar FLS system ........................................ 63

Testing operation of the Sonar Head ........................................................................... 63
Testing the Sonar Head telemetry................................................................................ 65

Turning off the M3 Sonar FLS ............................................................................................. 68

DRAWING FILE.......................................................................... 69

About the drawings in the drawing file................................................................................. 69
Sonar Head outline dimensions ............................................................................................ 70

TECHNICAL SPECIFICATIONS.................................................... 72

EQUIPMENT HANDLING ............................................................. 81

Transporting Kongsberg Mesotech equipment ..................................................................... 82

M3 Sonar FLS

Содержание M3 Sonar FLS



































































































Результаты поиска

Содержание M3 Sonar FLS

Отзывы:

Похожие инструкции для M3 Sonar FLS

Бренды по названию

Популярные бренды

Kongsberg M3 Sonar FLS, Руководство по установке

Результаты поиска

Содержание M3 Sonar FLS

Отзывы:

Похожие инструкции для M3 Sonar FLS

Бренды по названию

Популярные бренды