Kongsberg M3 Sonar FLS Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 98

background image

18

922-20297011/1.0

Installation requirements

Topics

Supply voltage requirements, page 18

Electromagnetic compatibility installation guidelines, page 18

Supply voltage requirements

Observe the general requirements related to the supply power.

The supply voltage must kept within ±10% of the installation’s nominal voltage. Maximum
transient voltage variations on the main switchboard’s bus-bars must not exceed -15% to
+20% of the nominal voltage (except under fault conditions).

Electromagnetic compatibility installation guidelines

Kongsberg Mesotech Limited equipment and accessories are compliant with applicable
electromagnetic compatibility (EMC) regulations. This compliance ensures electromagnetic
interference (EMI) between the system components and other on-board equipment is
minimized to reduce the risk of performance degradation due to such interference. Correct
installation is required to maintain electromagnetic compatibility.

Employ the following recommendations to ensure the best EMC performance:

• Use only Kongsberg-specified cables and check that any ferrite suppression filters fitted

on the cables are installed as per the installation drawings. Suppression ferrites are
important for minimizing electromagnetic interference. If one has to be removed during
the installation, re-install the suppression filter in its original position on the cable before
using the system.

• Use a ferrite suppression filter installed on any third-party-supplied cable end attached to

M3 Sonar FLS equipment ports.

• Operate using standard length system interconnect cables unless cutting or cable

extensions are described in the installation manual.

• Install M3 Sonar FLS equipment and interconnect cables as follows:

– At least 1 meter (3.3 feet) from any equipment transmitting radio signals, antennas or

cables connecting the radio equipment to the antennas.

– At least 2 meters (6.6 feet) from SSB radios, antennas, and cables.

M3 Sonar FLS Installation Manual

«
...
18
19
20
21
22
...
»

Содержание M3 Sonar FLS



































































































Отзывы:

Нет отзывов

Похожие инструкции для M3 Sonar FLS

Бренд: Sonic Страницы: 153

Бренд: Kongsberg Страницы: 298

COLOR SCANNING CSH-55

Бренд: Furuno Страницы: 68

FISHEASY 245DS - ADDITIONAL

Бренд: Eagle Страницы: 72

Бренд: Humminbird Страницы: 2

ICE HELIX CHIRP Series

Бренд: Humminbird Страницы: 4

Бренд: Humminbird Страницы: 6

Бренд: Humminbird Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды