Kongsberg M3 Sonar FLS Скачать руководство пользователя страница 70

Страница: 70 / 98

922-20297011/1.0

Turning off the M3 Sonar FLS

The M3 Sonar FLS is not provided with an on/off switch.

Context

When you do not use the M3 Sonar FLS, turn off the entire system.

Procedure

If you are running the sonar, click

Setup

→

Disconnect

in the M3 Sonar FLS software.

Switch off the Sonar Processor.

Close the M3 Sonar FLS software and any third-party software.

Shut down Windows.

Disconnect the power cord leading to the power supply.

Alternatively, switch off the breaker supplying power to the M3 Sonar FLS.

Switch off any additional items, such as a sound velocity profiler or display.

If required, refer to the instructions provided by the product’s manufacturer.

M3 Sonar FLS Installation Manual

Содержание M3 Sonar FLS



































































































Результаты поиска

Содержание M3 Sonar FLS

Отзывы:

Похожие инструкции для M3 Sonar FLS

Бренды по названию

Популярные бренды

Kongsberg M3 Sonar FLS, Руководство по установке

Результаты поиска

Содержание M3 Sonar FLS

Отзывы:

Похожие инструкции для M3 Sonar FLS

Бренды по названию

Популярные бренды