Komatsu WB93R-5 Скачать руководство пользователя страница 244 | Manualshive

Страница: 244 / 284

background image

AUTHORIZED OPTIONAL EQUIPMENT

242

6.1 AUTHORIZED OPTIONAL EQUIPMENT

CAUTION

q

Komatsu machines can be provided with optional equipment in addition to the standard equipment; if
optional equipment is installed and used, carefully read the relevant operation manual and keep to the
instructions given therein.

q

Use only optional or special equipment recommended and approved by Komatsu and in compliance
with the requirements indicated in the table. (See "6.1.2 PRECAUTIONS REGARDING THE INSTALLA-
TION OF EQUIPMENT").

q

Komatsu cannot be held liable for any injury, accident or product failure resulting from the installation
and use of unauthorized equipment.

6.1.1 PRECAUTIONS REGARDING SAFETY

The installation of optional accessories and equipment other than those authorized by Komatsu shortens the life of
the machine and may also cause safety problems.
It is advisable to contact a Komatsu Dealer before installing any accessory that is not mentioned in this operation
and maintenance manual.
In case of failure to comply with these instructions, Komatsu declines any responsibility for accidents or damage.

WARNING

q

When removing or installing any equipment, take the following precautions and be careful to ensure that
operations are carried out in total safety.

q

Carry out installation and removal on a firm and flat surface.

q

When the operations are carried out by two or more operators, decide the communication signals in ad-
vance and respect them during work.

q

Use a crane to handle objects weighing more than 25 kg.

q

Always support any heavy part before removing it. When lifting heavy parts, be always careful to the po-
sition of the centre of gravity of the object being handled.

q

It is dangerous to carry out any operation with suspended loads. Always position the load on a suitable
support and make sure that it is stable.

q

When installing or removing any equipment, make sure that it is stable and cannot fall down.

q

Never stand under loads being lifted by a crane.
Take care to choose a safe position, where you do not run any risk in case the load should fall down.

IMPORTANT

q

Specialized personnel is required to operate cranes. Do not allow unskilled personnel to use cranes.

For further details regarding installation and removal operations, contact your Komatsu Dealer.

https://tractormanualz.com

«
...
242
243
244
245
246
...
»

Содержание WB93R-5





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WB93R-5

Бренд: Gehl Страницы: 132

Бренд: Hyundai Страницы: 262

Бренд: IHI Страницы: 115

Бренд: Takeuchi Страницы: 182

Бренд: jcb Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды