Komatsu WB93R-5 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 284

background image

INSTRUMENTS AND CONTROLS

103

14 - FRONT LOADER SPEED CONTROL PUSH BUTTON

The push button (14) makes it possible to exploit the maximum
quantity of oil delivered by the hydraulic pump for heavy-duty
applications.
Press the push button to increase oil delivery; when the push
button is released, the oil delivery returns to the standard oper-
ating values.
It is advisable to use the push button without interruption for no
more than 5-6 seconds.

15 - DECLUTCH PUSH BUTTON

WARNING

q

Do not use this button for more than 15–20 seconds.

q

Do not use this button during travel on roads and espe-
cially when travelling downhill, since this function re-
leases the clutch and sets the machine in neutral.

The push button (15) is used to shift gears when the machine
is moving. (See "3.3.6 pos. 5 - GEARSHIFT LEVER").

16/17 - STABILIZER CONTROL LEVERS

WARNING

q

Before moving the machine, make sure that the stabiliz-
ers are completely raised.

q

When travelling on roads, raise the stabilizers and en-
gage the safety locks and the servo control locking de-
vice.

These levers are positioned to the operator’s left and control
the raising and lowering of the stabilizers, as indicated in the
diagram.

IMPORTANT

q

All movements are inhibited when the safety button (A)
is in locking position (LED on) (see "3.3.2 pos. 12 -
SERVO CONTROL LOCKING BUTTON").

RKAB4430

14

RKAB4440

15

RKAB4480

N

N

16

17

RKAB4450

A

https://tractormanualz.com

«
...
103
104
105
106
107
...
»

Содержание WB93R-5





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WB93R-5

Бренд: Case Страницы: 22

Бренд: jcb Страницы: 51

Бренд: Komatsu Страницы: 51

Бренд: Kanga Страницы: 69

Бренд: Kanga Страницы: 76

Бренд: Komatsu Страницы: 31

Бренд: Grizzly Страницы: 15

Бренд: Azbil Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды