Komatsu WB93R-5 Скачать руководство пользователя страница 165

Страница: 165 / 284

TROUBLESHOOTING

163

Steam comes out of radiator breather
pipe:

• Fluid level low, fluid leakages.

• Fan belt slackened.

• Radiator fins damaged or closed.

• Faulty thermostat.

• Radiator cap loose or broken. Work-

ing at considerable altitude.

• Top up, repair.

• Check belt tension.

• Repair or clean.

(•) Change.

• Tighten cap or change unit.

Temperature indicator always on the
right end of the scale:

• Faulty temperature indicator.

(•) Change.

Temperature indicator pointer always on
the left end of the scale:

• Faulty thermostat.

• Faulty indicator.

(•) Change.

Engine does not start:

• Run-down battery.

• Battery terminals loose or corroded.

• No fuel.

• Type of fuel unsuitable for climate.

• Air in fuel supply circuit.

•

Other causes

(•) Charge or replace.

(•) Tighten nuts or change terminals.

• Refuel.

(•) Change filter. Refuel with winter

type.

(•) Check pipes, connections, fuel and

injection pumps. Bleed circuit.

(•) Contact Dealer.

Engine stops:

• Fuel filters clogged.

• Air in fuel supply circuit.

• Other causes.

(•) Change.

(•) Check pipes, connections, fuel and

injection pumps. Bleed circuit.

(•) Contact Dealer.

Engine overheats:

• Radiator clogged.

• Insufficient tension of water pump

and fan belts.

• Low coolant.

•

Air filters clogged

• Clean fins.

(•) Check and adjust belt tension.

• Top up.

(•) Clean or change filters.

Engine power insufficient:

• Impurities or water in fuel supply cir-

cuit.

• Fuel filter clogged.

•

Air filters clogged

(•) Clean and refuel with new fuel.

(•) Change.

(•) Clean or change filters.

Exhaust gases white or light blue:

• Too much oil in oil pan.

• Unsuitable fuel.

• • Other causes

• Top up.

• Change with fuel in compliance with

standards.

(•) Contact Dealer

Exhaust gases occasionally tend to be
black:

• Air cleaner clogged.

• Faulty injectors.

• Clean or change.

(•) Change.

Combustion noise occasionally resem-
bles a blow:

• Faulty injectors.

(•) Change.

Abnormal noises (during combustion or
in mechanical parts):

• Fuel with low cetane rating.

• Overheating.

• Exhaust silencer inside damaged.

• Excessive valve clearance.

• Change with fuel in compliance with

standards.

• See “defects of temperature indica-

tor”.

(•) Change.

(•) Adjust valve clearance.

TROUBLE

CAUSE

REMEDY

https://tractormanualz.com

Содержание WB93R-5




























































































































































































































































































Результаты поиска

Содержание WB93R-5

Отзывы:

Похожие инструкции для WB93R-5

Бренды по названию

Популярные бренды

Komatsu WB93R-5, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание WB93R-5

Отзывы:

Похожие инструкции для WB93R-5

Бренды по названию

Популярные бренды