Komatsu D375A-8 Скачать руководство пользователя страница 241 | Manualshive

Страница: 241 / 466

Komatsu D375A-8 Скачать руководство пользователя страница 241

METHOD FOR TURNING THE MACHINE WHILE TRAVELING FORWARD

Tilt  the  joystick  (steering,  directional  and  gear  shift  lever)  for-
ward  and  tilt  it  to  the  left  side  (L)  halfway,  and  the  steering
clutch  is  disengaged  and  the  machine  gradually  turns  to  the
left.

REMARK

• To turn to the right gradually, tilt the joystick (steering, di-

rectional and gear shift lever) forward and tilt it to the right
halfway.
Perform the operation similarly for the reverse travel.

• To turn gradually for a long distance, repeat the short time

directional amendment for turning so that the durability of
brake is secured.

METHOD FOR MAKING PIVOT TURN WHILE TRAVELING FORWARD

Tilt the joystick (steering, directional and gear shift lever) for-
ward first and tilt it fully to the left (L), the steering clutch is cut
off and the steering brake is applied, then the machine makes
a pivot turn to the left.

REMARK

When making a pivot turn to the right while traveling forward,
tilt the joystick (steering, directional and gear shift lever) for-
ward and tilt it fully to the right (R).
Perform the operation similarly for the reverse travel.

METHOD FOR TURNING WHILE TRAVELING ON DOWNHILL

For this machine (machine available for pivot turn), performing the cross steering is restrained even when the
machine travels downhill on its own weight, or when the machine is pushed by the towing machine on a downhill
slope.

REMARK

The cross steering means the steering state that the operator performs the turning operation to one (e.g. right)
direction makes the machine turn to the opposite (e.g. left ) direction.

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-183

«
...
239
240
241
242
243
...
»

Содержание D375A-8



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды