Komatsu D375A-8 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 466

Komatsu D375A-8 Скачать руководство пользователя страница 129

REVERSE HYDRAULIC FAN

NOTICE

• After stopping the engine, check around the engine for

sticking dry leaves or dirt.
In particular, carefully check around the exhaust mani-
fold and turbocharger for sticking dirt which can
cause a fire.

• If the aftertreatment devices regeneration pilot lamp

(A)  lights  up  while  the  fan  rotates  in  reverse,  the  en-
gine  speed  may  decrease  to  1000 rpm,  regardless  of
the position of fuel control dial.
In  this  case,  the  fan  speed  also  decreases  and  suffi-
cient  air  flow  for  cleaning  the  radiator  cannot  be  ob-
tained. Accordingly, wait under this condition until af-
tertreatment  devices  regeneration  pilot  lamp  (A)  goes
out.
After  the  lamp  goes  out,  you  can  increase  the  engine
speed and make the fan rotate in reverse.

REMARK

If  the  fan  reverse  operation  is  performed  while  the  aftertreat-
ment  devices  regeneration  pilot  lamp  (A)  is  lit,  the  engine
speed  may  not  increase  even  if  the  fuel  control  dial  is  set  to
High idle (MAX) position, but this is not a failure.
The  hydraulic  fan  reverse  mode  (fan  reverse  rotation)  can  be
used to remove the insects and dirt sticking to the radiator core
by blowing air inward the machine with the fan.
Before  starting  the  hydraulic  fan  reverse  rotation,  check  that
there is no combustible substance in the periphery which may
be sucked in the fan nor the deposit of the soil around the fan.
If there is any deposit, remove it first.
1.

Set the parking brake lever and work equipment lock lever to LOCK positions.

2.

Perform the engine warm-up operation.
If the warm-up operation is not performed, the air flow may be insufficient.

3.

After the warm-up operation, turn the fuel control dial to Low idle (MIN) position.

4.

Stop the engine.

5.

Open the engine side cover on the right and left sides of the machine.

6.

Turn the starting switch to ON position.

7.

Select “Fan Reverse Mode” (1) on “Machine Setting” menu
(b) screen.

8.

Press the switch F6.

OPERATION

EXPLANATION OF COMPONENTS

3-71

«
...
127
128
129
130
131
...
»

Содержание D375A-8



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды