manualshive.com logo in svg

Komatsu D375A-8, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D375A-8 Скачать руководство пользователя страница 239

Shoe slip control mode

Changing the gear speed used while the machine is traveling

• During forward travel: The gear speed used can be set to

F1 to F3.

• During reverse travel: The gear speed used can be set to

R1 to R3.

UP switch (a): Each time this is pressed, gear speed used goes

up one range.

DOWN switch (b): Each time this is pressed, gear speed used

goes down one range.

REMARK

• In  the  automatic  gear  shift  mode,  if  the  maximum  gear

speed  has  been  changed  while  traveling,  return  the  joy-
stick  (steering,  directional  and  gear  shift  lever)  to  NEU-
TRAL  position.  The  setting  is  returned  to  the  maximum
gear speed set in the preset mode before starting to travel
(when the transmission has been at NEUTRAL).

• The preset cannot be changed during travel.
• In  the  shoe  slip  control  mode,  the  shoe  slip  control  func-

tions only in gear speed F1.

NOTICE

• Do not move close to the edge of a cliff unnecessarily.

When  dropping  soil  at  the  edge  of  a  cliff  to  build  an
embankment or landfill, always leave one load and use
the next load to push the previous load over.

• When passing over the top of a slope or when dump-

ing soil from a cliff, there is danger that the load on the
machine  will  suddenly  be  reduced  and  the  travel
speed will increase. In this case, depress the decelera-
tor pedal to reduce the travel speed.

• In the shoe slip control mode, when a load is applied,

the  gear  speed  automatically  shifts  down,  but  even
when the load is removed, the gear speed does not au-
tomatically shift up.

METHOD FOR SWITCHING BETWEEN FORWARD AND REVERSE

k

k

 WARNING

When  switching  the  travel  direction,  confirm  the  safety  in
the direction to select.
 

k

k

 CAUTION

You can switch the forward/reverse travel direction without
stopping  the  machine.  However,  for  the  safety,  operator
comfort,  and  service  life  of  the  power  train,  it  is  recom-
mended  not  to  switch  with  the  engine  at  full  throttle  but
depress the decelerator pedal, decrease the engine speed,
and then switch.
 

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-181

Содержание D375A-8



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды