manualshive.com logo in svg

Kolin KAM-75BMC, Руководство пользователя, Страница: 13 / 19

Поделиться
Скачать
Kolin KAM-75BMC Скачать руководство пользователя страница 13

9

9

1. To avoid vibration and noise, make sure the unit is installed securely and firmly.
2. Install the unit where the sunlight does not shine directly on the unit.

If the unit receives direct sunlight, build an awning to shade the cabinet.

3. There should be no obstacle, such as a fence or wall, within 50cm from the back of the

cabinet because it will prevent  heat radiation of the condenser.
Restriction of outside air will greatly reduce the cooling and heating efficiency of the 
air conditioner.

4. Install the unit a little obliquely outward not to leak the condensed water into the room

O

(about 3~4  with level).

5. Install the unit with its bottom portion 75~150cm above the floor level.
6. The power cord must be connected to an independent circuit. The yellow/green

wire must be grounded.

All side louvers of the cabinet must remain exposed to the outside of the structure.

CAUTION

Select the best location 

INSTALLATION INSTRUCTIONS 

75~150cm

Over 50cm

O

About 3~4

AWNING

FENCE

75

~150cm

Over 50cm

O

About 3~4

AWNING

FENCE

Step 1
Remove the air conditioner from it's packaging, remove fixing
screws and slide the air conditioner out of it's housing (Refer
to Installation Steps).
Step 2
Prepare the hole in the wall so that the bottom of the housing 
is well supported, the top has minimum clearance and the air 
inlet louvers have clearance as shown below in options  A and
B. Holes from the outside through to the cavity should be 
sealed. The housing should slope down towards the rear by 
about 5mm to allow water formed during operation to drain.
Step 3
Install the housing into the wall and secure. Ensure the foam
seals are not damaged. Flash, seal or fill gaps around the 
inside and outside to provide satisfactory appearance and 
protection against the weather, insects and rodents.

Installation of the Housing 

NOTE: UNIT MAY BE SUPPORTED BY A 

  SOLID FRAME FROM BELOW OR 
  BY A HANGER FROM A SOLID
  OVERHEAD SUPPORT.

Preferred method of installation into a timber 
framed wall, partition or window.

FLASH OR SEAL AROUND EXTERNAL 
WALL FRAME OR ARCHITRAVE

STURDY TIMBER
FRAME ALL ROUND 
UNIT

TIMBER FRAMED 
WALL OR PARTITION

EXTERNAL SUPPORT 
FRAME AT BALANCE
POINT OF A/C

ALTERNATIVELY, BRACKETS 
AS ILLUSTRATED BELOW
MAY BE USED.

DRAIN PAN

Содержание KAM-75BMC




















Отзывы:

Нет отзывов