background image

24

1058907-W2-J

Rada is a registered trade mark of 

Kohler Mira Limited.

The company reserves the right to alter 

14648

0844 571 1777

Fax: 0844 472 3076

Email – Visit 

[email protected]

 

By  Post:

 

Rada  Controls,  Cromwell  Road, 

Cheltenham, Gloucestershire GL52 5EP

To Contact Us: Eire Only

01 531 9337

E-mail: 

[email protected]

Calls cost 7p per minute plus your phone company’s 
access charge

Guarantee 

guarantee which starts from date of purchase.

 

Within 

the  guarantee  period  we  will  resolve  defects  in 

materials or workmanship, free of charge, by repairing 

or replacing parts or product as we may choose.

This  guarantee  is  in  addition  to  your  statutory 

rights and is subject to the following conditions:

  ●  The product must be installed and maintained 

   in accordance with the instructions given in this 

   user guide.

  ●  Servicing must only be undertaken by us or our 

   appointed representative. 

Note!

 If a service visit 

   is required the product must be fully installed and 

   connected to services.

  ●  Repair under this guarantee does not extend 

   the original expiry date. The guarantee on any 

   replacement parts or product ends at the original 

   expiry date.

  ● 

   reserve the right to supply replacement parts only.

The guarantee does not cover:

  ●  Call out charges for non product faults (such as 

   damage or performance issues arising from 

   incorrect installation, improper use, inappropriate 

   cleaning, lack of maintenance, build up of 

   limescale, frost damage, chemical attack, 

   

   where no fault has been found with the product.

  ●  Water or electrical supply, waste and isolation 

   issues.

  ●  Compensation for loss of use of the product or 

   consequential or indirect loss of any kind.

  ●  Damage or defects caused if the product is 

   

   us or our appointed representative. 

  ●  Routine maintenance or replacement parts to 

   comply with the requirements of the TMV2 or 

   TMV3 healthcare schemes

  ●  Accidental or wilful damage. 
  ●  Products purchased ex-showroom display.

What to do if something goes wrong

If your product does not work correctly refer to this 

manual  for  fault  diagnosis  and  check  that  it  is  in-

stalled  and  commissioned  in  accordance  with  our 

instructions.If this does not resolve the issue, contact 
us for help and advice.

Technical Helpdesk Service

Contact  our  Customer  Services  Team  for 

product  advice,  to  purchase  spare  parts  or 

accessories or to set up service visit. You can contact 

us via phone or e-mail - contact details below.

Please  provide  your  model  name,  power  rating  (if 

applicable) and date of purchase.

Rada Website (www.radacontrols.com)

From our website you can view our full product 

catalogue or download a brouchure.

Spares and Accessories

We hold the largest stocks of genuine Rada 

spares and accessories.

Service/Repairs

No one knows our products better than our 

nationwide team of Service Technicians. We 

can carry out service or repair work to your product  

both during and after the guarantee period.

You have the assurance of a fully trained Technician, 

genuine Rada spare parts and a 12 month guarantee 

on any chargeable work done.

Service Contracts

Regular servicing ensures your product continues to 

operate at the peak of performance. We offer annual 

or bi-annual servicing carried out by our fully trained 

technicians subject to site survey

To Contact Us - UK Customer Service & 

Your product has the benefit of our manufacture's

For shower fittings or consumable items we

corrosion, system debris or blocked filters) or

repaired or modified by persons not authorised by

Specification Enquiries

product specifications without notice.

© Kohler Mira Limited, December 2016

CUSTOMER SERVICE

Содержание rada Thermotap-3

























Отзывы: