background image

10

1058907-W2-J

Thermotap-3 Installation

'O' Seal

30 mm 

Maximum

Backplate 

(Reverse to suit 

smaller basin hole)

Fixing Nuts

Rigid Tail 

option

Washer

Checkvalve 

Assembly

Strainer

Isolating 

Valve

Fixing Studs

26 to 36 mm 

Diameter

Union Nut

Flexible 

Tail option

Installation

1.

  Screw the fixing studs fully into the 

Thermotap-3 body.

2.

  Place the 'O' seal in the groove in 

the base of the Thermotap-3 body.

3. 

Place either rigid or flexible inlet 

tail through one of the larger holes 

in the backplate, orientate the 

backplate to suit the hole size in 

the basin.

5. 

Working  underneath  the  basin 

offer the inlet tail up through the 

hole in the basin.

4.

  Screw  inlet  tail  (if  using  flexible 

type, red coloured hose) into the 

Thermotap-3, hole marked with a 

RED label (nearest the spout) and 

tighten. Position tap on basin.

5.

  Pull the backplate over the fixing 

studs.

6.

  Working  underneath  the  basin, 

locate  other  inlet  tail  (blue 

coloured  flexible  hose)through 

backplate then screw and tighten 

into remaining hole in tap, spread 

tails apart slightly if necessary to 

assist in fitting.

7.

  Make sure that the Thermotap-3 

is correctly positioned and screw 

the fixing nuts onto the fixing 

studs. Tighten the fixing nuts 

until the tap is secure. DO NOT 

OVERTIGHTEN.

8.

  Connect the isolating valves 

to the supply pipework. Fit the strainer into the isolating valve and screw in 

the checkvalve housing. Use a suitable spanner to tighten the checkvalve 

assemblies.

9. 

Locate the sealing washers inside the nuts on the inlet tails and screw onto the 

checkvalve assemblies. Please ensure that the inlet tail (red coloured  flexible 

hose) previously connected to hole marked with a RED label is connected to 

hot supply. Use a suitable spanner to tighten the union nuts.

10.

  Restore the water supplies and check all connections are watertight. Refer to 

section 

'Commissioning'

.

Содержание rada Thermotap-3

























Отзывы: