Kohler KS530 Скачать руководство пользователя страница 30

Страница: 30 / 92

Fuel System

KohlerEngines.com

22 690 01 Rev. --

Carburetor Circuits
Float

Fuel level in bowl is maintained by ﬂ oat and fuel inlet

needle. Buoyant force of ﬂ oat stops fuel ﬂ ow when

engine is at rest. When fuel is being consumed, ﬂ oat will

drop and fuel pressure will push inlet needle away from

seat, allowing more fuel to enter bowl. When demand

ceases, buoyant force of ﬂ oat will again overcome fuel

pressure, rising to predetermined setting and stop ﬂ ow.

Slow and Mid-Range

At low speeds engine operates only on slow circuit. As

a metered amount of air is drawn through slow air bleed

jets, fuel is drawn through main jet and further metered

through slow jet. Air and fuel are mixed in body of slow

jet and exit to idle progression (transfer port) chamber.

From idle progression chamber, air fuel mixture is

metered through idle port passage. At low idle air/fuel

mixture is preset and not adjustable. This mixture is then

mixed with main body of air and delivered to engine.

As throttle plate opening increases, greater amounts of

air/fuel mixture are drawn in through ﬁ xed and metered

idle progression holes. As throttle plate opens further,

vacuum signal becomes great enough at venturi so main

circuit begins to work.

Main (high-speed)

At high speeds/loads engine operates on main circuit.

As a metered amount of air is drawn through air jet,

fuel is drawn through main jet. Air and fuel are mixed

in main nozzle then enters main body of airﬂ ow where

further mixing of fuel and air occurs. This mixture is then

delivered to combustion chamber. Carburetor has a ﬁ xed

main circuit; no adjustment is possible.

Carburetor Adjustments

NOTE: Carburetor adjustments should be made only

after engine has warmed up.

Carburetor is designed to deliver correct fuel-to-air

mixture to engine under all operating conditions. Main

fuel jet is calibrated at factory and is not adjustable. Idle

fuel is also set at factory and is not adjustable.

Low Idle Speed (RPM) Adjustment

NOTE: Actual low idle speed depends on application.

Refer to equipment manufacturer’s

recommendations.

1. Low idle speed (without governor) for basic engines

is 1200 RPM (± 75 RPM). This can be adjusted by

holding throttle lever against stop and turning low

idle speed screw in or out.

2. These engines have governed idle. To set to

manufacturer's recommendation, turn adjustment

screw on speed control bracket in (clockwise) to

increase or out (counterclockwise)to decrease RPM

speed.

High Speed (RPM) Adjustment

1. With engine running, move throttle control to fast

and pin.

2. Loosen speed control bracket mounting screws,

slide bracket to adjust high speed setting, then

tighten screws.

Carburetor Servicing

NOTE: Main and slow jets are ﬁ xed and size speciﬁ c.

Fixed jets for high altitudes are available.

● Inspect carburetor body for cracks, holes, and other

wear or damage.

● Inspect ﬂ oat for cracks, holes, and missing or

damaged ﬂ oat tabs. Check ﬂ oat hinge and shaft for

wear or damage.

● Inspect fuel inlet needle and seat for wear or damage.

● Inspect spring loaded choke plate to make sure it

moves freely on shaft.

1. Perform removal procedures for appropriate air

cleaner and carburetor outlined in Disassembly.

2. Clean exterior surfaces of dirt or foreign material

before disassembling carburetor. Remove bowl

retaining screws and carefully separate fuel bowl

from carburetor body. Do not damage fuel bowl

O-rings. Transfer any remaining fuel into an

approved container. Save all parts.

3. Remove ﬂ oat pin, ﬂ oat, and inlet needle. Seat for

inlet needle is serviceable by replacing carb spacer

(inlet seat assembly). Remove carb spacer by

carefully lifting up and oﬀ carburetor body.

NOTE: Lift straight up and not sideways to ensure main

tube isn't damaged.

4. Main jet can be removed from carb spacer by using

a blunt tool and gently pushing jet out of center

stem. Main jet is retained in carb spacer by O-ring.

Inspect O-ring during disassembly and replace if

damaged. Repair kits are available for both gravity

and fuel pump equipped engines.

5. Clean carburetor bowl and assembly as required.
6. See illustration for carburetor components on page

28. Note O-ring on carb spacer to carburetor body

and fuel bowl, inlet seat/spacer well and main jet.

Cleaning of passages and oriﬁ ces can be done

using compressed air. Do not use wire or carburetor

cleaner.

7. After cleaning, inspect choke shaft and choke valve

assembly for wear. Replace as required with choke

shaft kit. To install kit go to step 8, otherwise go to

step 10. Inspect throttle shaft and throttle valve

assembly. If wear is found on throttle shaft, install

throttle shaft kit. To install kit go to step 10, otherwise

go to step 12. If wear is noted within choke and/or

throttle shaft bores of carburetor body, a complete

carburetor replacement is recommended.

Содержание KS530




























































































Результаты поиска

Содержание KS530

Отзывы:

Похожие инструкции для KS530

Бренды по названию

Популярные бренды

Kohler KS530, Руководство по обслуживанию

Результаты поиска

Содержание KS530

Отзывы:

Похожие инструкции для KS530

Бренды по названию

Популярные бренды