Kohler KS530 Скачать руководство пользователя страница 71

Страница: 71 / 92

Disassembly/Inspection and Service

22 690 01 Rev. --

KohlerEngines.com

Remove Connecting Rod and Piston

Connecting Rod

Screw

Rod Cap

Piston Assembly

Connecting Rod

NOTE: If a carbon ridge is present at top of bore, use a

ridge reamer to remove it before attempting to

remove piston.

1. Rotate crankshaft so rod journal is in 8 o’clock

position.

2. Remove screws and connecting rod cap.
3. Carefully push connecting rod and piston away from

crankshaft and out of cylinder bore.

Inspection and Service

Check bearing area (big end) for score marks and

excessive wear. Service replacement connecting rods

are available in STD crankpin size.

Remove Piston from Connecting Rod

Piston Pin Retainer

Piston Pin

Piston Assembly

Connecting Rod

Remove piston pin retainers and piston pin. Separate

piston from connecting rod.

Piston and Rings Inspection

Scuﬃ ng and scoring of pistons and cylinder walls occurs

when internal temperatures approach welding point

of piston. Temperatures high enough to do this are

created by friction, which is usually attributed to improper

lubrication, and/or overheating of engine.

Normally, very little wear takes place in piston boss-

piston pin area. If original piston and connecting rod

can be reused after new rings are installed, original pin

can also be reused, but new piston pin retainers are

required. Piston pin is part of piston assembly; if pin boss

or pin are worn or damaged, a new piston assembly is

required.
Ring failure is usually indicated by excessive oil

consumption and blue exhaust smoke. When rings fail,

oil is allowed to enter combustion chamber where it is

burned along with fuel. High oil consumption can also

occur when piston ring end gap is incorrect because

ring cannot properly conform to cylinder wall under this

condition. Oil control is also lost when ring gaps are not

staggered during installation.
When cylinder temperatures get too high, lacquer and

varnish collect on pistons causing rings to stick which

results in rapid wear. A worn ring usually takes on a

shiny or bright appearance.
Scratches on rings and pistons are caused by abrasive

material such as carbon, dirt, or pieces of hard metal.
Detonation damage occurs when a portion of fuel charge

ignites spontaneously from heat and pressure shortly

after ignition. This creates two ﬂ ame fronts that meet and

explode to create extreme hammering pressures on a

speciﬁ c area of piston. Detonation generally occurs from

using low octane fuels.
Preignition or ignition of fuel charge before timed spark

can cause damage similar to detonation. Preignition

damage is often more severe than detonation damage.

Preignition is caused by a hot spot in combustion

chamber from sources such as glowing carbon deposits,

blocked ﬁ ns, improperly seated valve, or wrong spark

plug.
Replacement pistons are available in STD bore size.

Replacement pistons include new piston ring sets and

new piston pins.
Replacement ring sets are also available separately

for STD pistons. Always use new piston rings when

installing pistons. Never reuse old rings.

Remove Piston Rings

1. Remove top and center compression rings using a

ring expander.

2. Remove oil control ring rails, then remove spacer.

Содержание KS530




























































































Результаты поиска

Содержание KS530

Отзывы:

Похожие инструкции для KS530

Бренды по названию

Популярные бренды

Kohler KS530, Руководство по обслуживанию

Результаты поиска

Содержание KS530

Отзывы:

Похожие инструкции для KS530

Бренды по названию

Популярные бренды