Kohler KS530 Скачать руководство пользователя страница 39

Страница: 39 / 92

Governor System

22 690 01 Rev. --

KohlerEngines.com

This governor design works as follows:
● Centrifugal force acting on rotating governor gear

assembly causes ﬂ yweights to move outward as

speed increases. Governor spring tension moves

them inward as speed decreases.

● As ﬂ yweights move outward, they cause regulating pin

to move outward.

● Regulating pin contacts tab on cross shaft causing

shaft to rotate.

● One end of cross shaft protrudes through crankcase.

Rotating action of cross shaft is transmitted to throttle

lever of carburetor through external throttle linkage.

● When engine is at rest, and throttle is in fast position,

tension of governor spring holds throttle plate open.

When engine is operating, governor gear assembly is

rotating. Force applied by regulating pin against cross

shaft tends to close throttle plate. Governor spring

tension and force applied by regulating pin balance

each other during operation, to maintain engine

speed.

● When load is applied and engine speed and governor

gear speed decreases, governor spring tension moves

governor arm to open throttle plate wider. This allows

more fuel into engine, increasing engine speed. As

speed reaches governed setting, governor spring

tension and force applied by regulating pin will again

oﬀ set each other to hold a steady engine speed.

Governor Adjustments

NOTE: Do not tamper with governor setting. Overspeed

is hazardous and could cause personal injury.

Initial Adjustment Procedure

Make this adjustment whenever governor arm is

loosened or removed from cross shaft. Adjust as follows:
1. Make sure throttle linkage is connected to governor

arm and throttle lever on carburetor.

2. Loosen nut holding governor lever to cross shaft.
3. Move governor lever toward carburetor as far as it

will go (wide open throttle) and hold in this position.

4. Grasp cross shaft with a pliers, and turn shaft

counterclockwise as far as it will go. Torque nut to

7.7 N·m (68 in. lb.).

Governor Sensitivity Adjustment

Governor sensitivity is adjusted by repositioning

governor spring in holes in governor lever. If speed

surging occurs with a change in load, governor is set too

sensitive. If a big drop in speed occurs when a normal

load is applied, governor should be set for greater

sensitivity.
Desired high speed setting (RPM) will determine

governor spring used.

Содержание KS530




























































































Результаты поиска

Содержание KS530

Отзывы:

Похожие инструкции для KS530

Бренды по названию

Популярные бренды

Kohler KS530, Руководство по обслуживанию

Результаты поиска

Содержание KS530

Отзывы:

Похожие инструкции для KS530

Бренды по названию

Популярные бренды