background image

FLEUR

 WATER-GUARD

SIPHON JET

 

TOILET

110870-0489

Copyright 

 1989 Kohler Co.

INTRODUCTION

This service module will help you to understand the opera

tion and repair  of  the  K-3417  Fleur 

  Water-Guard Toi

let.

THEORY OF OPERATION

All the water in a close coupled toilet is held in a tank that is

above the rim of the bowl. Water to the rim and siphon jet is
supplied by gravity.
When the toilet is flushed, the water in the tank is directed to

the rim holes and the siphon jet. The siphon jet is located in
an area where it can quickly force water over the upleg of

the trap. This causes a more direct siphon action that
quickly removes waste from the bottom of the bowl. 

Refer

to Figs. #1 - #4

.

Toilet bowls for tank type or tankless toilets come in differ

ent heights. This does not affect the operation of the toilet
  but the heights are specified for specific reasons. Most

toilet bowls are 14" - 15" from the floor to the top of the
bowl rim. This standard height is considered the most com

fortable for the average adult to use.
When the toilet is flushed, the water in the tank is directed

to the rim holes and the siphon jet. The siphon jet is located
in an area where it can quickly force water over the upleg of

the trap. This causes a more direct siphon action that
quickly removes waste from the bottom of the bowl. 

Refer

to Figs. #1 - #4

.

ROUGHINGIN AND
INSTALLATION CONSIDERATIONS

The Kohler Fleur Toilet is perfect for remodeling and new in
stallations.  There are two installation considerations

unique to the Feur toilet. The first is the procedure for re
moving the tank lid.  To remove the tank lid, it is necessary

to remove the actuator.  To do this, place the palm of  your
hand over the actuator, and rotate your hand clockwise.

Continue this procedure until the actuator  unscrews from
tank lid.   The tank  lid can now be lifted off  the tank.  It is also

important to recognize that the air bags in the tank should
be removed and discarded before installing the tank.   

Re

fer to the roughingin drawings Fig. #5.   For  flush valve

SIPHON JET FLUSHING SEQUENCE

 Fig. #1  

 Fig. #2  

 Fig. #3  

 Fig. #4  

Содержание K-3417 Fleur








Отзывы: