background image

 Settings

 CAUTION

1.  Incorrect wiring to the sensor head or power/switch cables creates the risk of damage to both the controller and sensor head. Confirm 

that wiring is correct before turning on power.

2.  Record write conditions that were configured by writing them to flash memory.  Note that flash memory has a limited life, and the 

number of guaranteed writes is 10,000.

 Preparation for settings

  Connect the sensor head and power/switching cable to the controller.  Refer to "Attaching and detaching of the sensor head and power 

supply/switching cables" on page 

848.

 Configuring settings

First specify the built-in cylinder type (SET2) and then configure other settings as shown below.
You can change settings using the procedure below.

General flow

Description

Initial value

Sets the output range of each 
channel.

HI: 60 LO:40

Selects the model of mounted 
cylinder.

10

Selects the output mode of 
each channel.

CO4

Can be used to invert the 
switch output of each channel.

S-0

Changes the sensor head 
LED indicator.

HI: 60 LO:40

Configures the scaling setting. OFS: 0 FS: 100

Configures the display panel 
setting.

bL-1

Configures the LCD display 
cycle.

dT-1

Adjusts the switch output 
response time of each channel.

Sd-1

Performs initialization 1.

Performs initialization 2 
(display, output check).

Adjusts the maximum output 
voltage of analog output.

Note  1:   Be  sure  to  specify  the  model  of  cylinder  for  mounting.  

Failure to do so creates the risk of erratic operations.

 

  2:   Since initialization (SET A, SET B) returns settings to their 

initial defaults, all data settings to date are lost.

Detection 

mode

Button operation

Press

LCD

Button operation

Release

LCD

Press

Doing nothing returns to detection mode.

LCD ON/OFF
When a value 
is displayed, 
enters the 
detection 
mode.

LCD 
backlight 
becomes 
brighter.

increases 

value.

 

decreases 

value.

Changes in 
accordance 
with setting 
details.

Note2

Note1

2

駆動機器図面

エアシリンダ

三校

855

旧版

12

03̲2016

Содержание ZL1 Series















Отзывы: