manualshive.com logo in svg

Kodak Kodak DryView 8600, Руководство пользователя

Поделиться
Скачать
Kodak Kodak DryView 8600 Скачать руководство пользователя страница 54

Section 5 – Troubleshooting

5-7 

2000 March Rev. B    8186546

Clearing Film Jams – General

The film jam areas referred to in local display error messages are shown in
Figure 5-1.

A is the film tray area, where film misfeeds can possibly occur.

B and C identify the rollers on either side of the exposure area.

D and E identify the developer and film exit areas.

A

8300–1
83L

D

C

B

E

Film Tray

Figure 5-1. Possible Film Jam Locations

The following pages provide procedures for clearing film jams from all the areas
identified above. Before performing any of the procedues you must install the film
saver on the film tray, and remove the film tray from the machine.

 Note

Shutting off power to clear a film jam is not required. Shutting off the power
deletes all currently acquired (but unprinted) images and may clear some
error messages. If you do this, you will have to resend the unprinted images to
the imager.

Содержание Kodak DryView 8600














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды