Kodak Kodak DryView 8600 Скачать руководство пользователя страница 49

Страница: 49 / 77

DryView 8600 User Guide

5-2

8186546 2000 March Rev. B

Message

Operator Action

A TO D CONVERTER FAILURE (88)

POWER IMAGER OFF, THEN BACK ON

Power the imager off, wait 10-20
seconds, then power back on. If
message reappears, call for service.

CALIBRATION FAILED (69)

PRESS ENTER TO LOAD DEFAULT GAMMA

TABLES

Press Enter. Then stand by while
imager automatically loads default
tables. Make sure to check image
quality.

CALIBRATION FAIL: Dmin HI, Dmax XXX.X (70)

PRESS ENTER TO BUILD GAMMA TABLES

Press Enter. Then stand by while
imager automatically builds gamma
tables. If image quality is unacceptable,
use new film.

DEVELOPER OVER TEMPERATURE (17)

POWER IMAGER OFF, THEN BACK ON

Unable to control temperature. Power
imager off, wait 10-20 seconds, then
power back on. If message reappears,
call for service.

DEVELOPER UNDER TEMPERATURE (19)

POWER IMAGER OFF, THEN BACK ON

Unable to control temperature. Power
imager off, wait 10-20 seconds, then
power back on. If message reappears,
call for service.

DOUBLE FILM FEED – REMOVE MISFEED (24)

INSERT FILM SAVER TO REMOVE FILM TRAY

Insert the film saver and remove the film
tray. Discard any sheets of film that are
jammed in the machine. If problem
persists, call for service.

DYNAMIC RAM FAILURE (72)

CALL SERVICE – PRESS ENTER TO CONTINUE

Power imager off, wait 10-20 seconds,
then power back on. If message
reappears, call for service.

FILM TRAPPED INSIDE EXPOSURE AREA (23)

CALL SERVICE – IMAGER IS INOPERABLE

Insert the film saver. Raise the cover
and remove the film from the exposure
area. Close the cover and remove the
film saver. Press Enter to continue. If
film can’t be removed, call for service.

FILM TRAY EMPTY – INSERT FILM (29)

Imager is out of film. Remove film tray
and load a new film package.

FILM TRAY UNLOCKED (11).

INSERT FILM TRAY FULLY TO CLEAR ERROR

Remove and reinsert film tray into
Imager.

Содержание Kodak DryView 8600














































































Результаты поиска

Содержание Kodak DryView 8600

Отзывы:

Бренды по названию

Популярные бренды

Kodak Kodak DryView 8600, Руководство пользователя

Результаты поиска

Содержание Kodak DryView 8600

Отзывы:

Бренды по названию

Популярные бренды