Ko Propo EX-RR Скачать руководство пользователя страница 6

Страница: 6 / 57

② Attach the monitor bracket to the master

　unit. ※［ A ▼］mark to the steering side.

② Attach the monitor bracket to the master unit.

　 ※ Apply［ B ▼］ mark to the steering side.

① Attach a monitor base parallel to Xpansion

　unit. ※ Factory setting.

※ The disassembly method is the same as side
　and front positions.

① Attach the monitor base at a right angle to

　Xpansion Unit. ※ Different Factory setting.

Attention to the marker.

M2.6-6BH

M2-6
cap screw

screw used.

x 2

x １

x ４

2.6-8BH
Self tapping
screws

Nut Holder

Connect the wire of the
Xpansion unit to the
master unit.

③ Attach expansion unit to a master unit.

③ Attach the Xpansion unit to the master unit.

　※ Attach the monitor base and bracket as

　　shown in figure A ③ .

1.Remove M2-6 Cap Screw.
2.Slide the Xpansion like shown in the figure
　below and take off.

While matching the edge of the base with

the dent of the bracket, slide it until the

Xpansion unit locks.

Set M2-6 Cap Screw.

A ▼：setting to the front

Xpansion unit can be mounted facing the

front or the side. The factory setting is

mounted to the front.

▼ B：when mounting sideways

How to disassemble the Xpansion unit.

Remove the connector cover before use.

When assembling or disassembling the Xpansion unit to
EX-RR, please switch off the EX-RR.

Be careful to not misuse the M2.6-6BH and TP2.6-
8BH screws.

Xpansion unit can be mounted in two different
directions using the monitor base and bracket.

● Installation of Xpansion unit

Содержание EX-RR

























































Результаты поиска

Содержание EX-RR

Отзывы:

Бренды по названию

Популярные бренды

Ko Propo EX-RR, Инструкция по эксплуатации

Результаты поиска

Содержание EX-RR

Отзывы:

Бренды по названию

Популярные бренды