KNX GIRA 5110 00 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 42

background image

Safe-state mode

RF/TP media coupler/repeater | Order no. 5110 00 | 51103300

Page 38 of 42

9

Safe-state mode

Function of the safe-state mode

If the device does not work as intended, e.g. as a result of errors in the project design
or during commissioning, the execution of the loaded application program can be hal-
ted by activating the safe-state mode. In safe-state mode, essential functions of the
device are deactivated. Only the ETS diagnosis function can be executed, and it is
still possible to program the device.

When safe-state mode is active, the device acts as follows:

–

No group telegrams, physically addressed telegrams or broadcast telegrams
are forwarded (the routing is inactive).

–

The repeater function is inactive (no RF telegrams are repeated).

–

The configuration lock is inactive.

–

The status LED flashes red slowly.

If the device is working exclusively as a repeater (physical address
x.y.1...255), it is only possible to program the application program and read out
device information via the RF side! Thus, the configuration lock is always act-
ive on the TP side. In this case, the lock cannot even be released in safe-state
mode.

Activating the safe-state mode

￭

Disconnect the device connection terminal.

￭

Hold down the programming button.

￭

Reconnect the device connection terminal.

The device restarts. The status LED briefly lights up red and then yellow.

￭

Release the programming button as soon as the status LED starts flashing red
slowly.

Safe-state mode is active.

Deactivating safe-state mode

Safe-state mode is deactivated via the ETS or by disconnecting and reconnecting the
device voltage supply.

Precondition: Safe-state mode is active.

￭

Reset the device via the ETS (restart).

or

￭

Program the physical address with the help of the ETS.

or

￭

Disconnect the device connection terminals or switch off the voltage supply.

￭

Wait about 3 s.

«
...
36
37
38
39
40
...
»

Содержание GIRA 5110 00











































Отзывы:

Нет отзывов

Похожие инструкции для GIRA 5110 00

Бренд: Cantherm Страницы: 11

Бренд: KEB Страницы: 5

Бренд: ElectrIQ Страницы: 23

Бренд: Global Industrial Страницы: 27

Бренд: Qlima Страницы: 164

Бренд: Circutor Страницы: 9

Бренд: YOKOGAWA Страницы: 4

Бренд: CSI Страницы: 36

Бренд: ECO-heater Страницы: 9

Бренд: Exibel Страницы: 5

Бренд: Widney Страницы: 28

Бренд: Bionaire Страницы: 19

Бренд: Anslut Страницы: 9

Бренд: VEAB Страницы: 28

Бренд: Flagro Страницы: 18

LDHR012-200KB-S

Бренд: Garden Furniture Centre Страницы: 14

Apply air Aria 3 12400011

Бренд: Tecnosystemi Страницы: 24

TOR 21.1507 DPX

Бренд: Timberk Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды